Solar LED Street Lights Manufacturer 2500 Lumens equal to 150w HPS lamp!

IQ Solar LED Street Lighting If you can dream it, We can illuminate.

IQLED solar led illumination 2500 Lumens equal to 150 HPS lamps NEW 2010 IQLED!

Solar LED Lighting 2500 Lumens (Equal to 150w HPS Lamp), Running Time Dusk to Down, World Zone 4 (4-5 Hours of Daily Solar Radiation).

Luminous LED initial Flux: 2,500lm (equal to 75w HPS Lamp on 25 feet {7.7 meters} height pole or 150w HPS lamp on 20 feet {6 meters} Height Pole).
IP Rating: IP65

for this Green Energy Efficient and Safe Solar LED Park Lighting

Lamp’s Efficiency (%) ＞90%
Illumination (E) (Height=6 m )≥13 lux（Equal to HPS 33 lux） (Height=8 m ) ≥7.5 lux（Equal to HPS 19 lux） (Height=10 m )≥4.5 lux（Equal to HPS 11 lux） (Height=12 m )≥3 lux（Equal to HPS 7.5 lux）
Effective Illuminated Area 20×8 m (Height=6 m ) 26×10 m (Height=8 m ) 33×13 m (Height=10 m ) 40×16 m (Height=12 m )

When the installation height is 12m, the beam pattern is 40x16m rectangular , and the radiation-efficiency is more than 70% in the effective region, the total transparence is more than 90%, the possibility to reduce the loss of the light reaches the maximum. The illumination uniformity is very good in the effective radiation region, even it is better than grade of 0.5 and higher than the highest grades of 0.4 of the state road’s standards. The edge of the beam pattern is very clear and slide, no adverse glare is out of the effective radiation region, it causes no light pollution, it is an idea to cut-lighting lamp and meet the requirements of the road lighting or other special lighting, which can also be widely used for the special requirements such as street lighting, advertising lighting.

Beam Pattern is rectangular (rectangle) and good illumination uniformity, brightness difference is very little between the spot of center and periphery. Almost no difference in the direction of extending the road completely with the continuous extension of the road, it is the ideal lighting lamps for road lighting.

Solar LED Street Lights, Solar Light, Solar Lights, Solar Lighting, Solar Roadway Lights, Solar LED Light, Off Grid Light, street and area lighting, Solar Street Lights-Solar Street Lighting

Parking Lot Lights using solar and LED technology. Commercial solar LED lights for security area lighting LED parking lot lighting to save installation and running costs. Installing solar LED lighting in a parking lot means years of maintenance-free operation one thing less to worry about! You can easily install one solar powered parking lot pole
solar LED parking lot lighting you place the lights exactly where you want them NOT cutting or trenching. Each light is independently powered by a solar Panel mounted on the light itself. It operates independently from all the other solar led lights in the lot.
Parking Lot Lights, using solar power turns a necessity into a benefit: Solar Parking lot lights are a necessity for safety reasons. They are service lights, solar Parking lots are unrelated to the core business, hotels and resorts solar Parking lots, universities solar Parking lots and colleges solar Parking lots, parking malls and corporate complex, government solar Parking lots.

solar street lights, street lights, street lighting, traffic lights, area lighting, Solar LED Street Lights, powerful street and area lighting

Solar Street Lights, efficient and affordable street lighting systems for streets parking lots, parks and area lighting. We help you design and configure reliable solar street lights systems

LED Solar LED Streetlight

Solar LED Lighting for National Parks.
Solar Lighting Area Lighting Green Illuminations General Illumination Systems for Effective area lighting will maintain nighttime safety and security, but in many cases, a reliable source of electricity may be unavailable or too costly to access - until now. OkSolar-powered Green general illumination systems offer a convenient, affordable and environmentally friendly way to add outdoor area lighting anywhere, anytime for an limitless number of applications Solar LED Lighting for National Parks.

for this Green Energy Efficient and Safe Solar LED Park Lighting

Custom Solutions for Solar LED Lighting for National Parks LED Solar LED Streetlight Green illumination combination of solar wind

Custom Solutions for LED Solar LED Streetlight Green illumination combination of solar wind and fuel cells

Contact US today!

Lighting Outdoor Area Fixtures Roadway Fixtures
if you are looking for LED Street Lights, LED Streetlights, LED Street Lamps, Retrofit LED Street Lights, Solar LED Street Lights, LED Traffic Lights, LED Traffic Signals, Retrofit LED Modules, High Power LED Bulbs, LED Lamps, LED Spot Lamps or some other customized LED Lighting products, Please do not hesitate to contact NOW! The crisp white light produced by LEDs can significantly enhance nighttime visibility compared with the cloudy orange light produced by high pressure sodium.

Shoebox light

New! Streetlight Retrofits: Shoebox, drop down, acorn and cobra head LED streetlight retrofit solutions.

Vandal Protection Shields for Roadway, Street, Area, Outdoor and Flood Lights, Designed to stop small arms fire .22 to .44 caliber Utilities and municipalities have been turning to use of OkSolar Vandal Shields to help eliminate the problem of vandalism for good. Vandal Shields offers an exclusive line of bullet-resistant, vandal-proof polycarbonate shields designed protect outdoor lighting fixtures from the abuses of vandalism. Shields are proven to withstand the impacts of rocks, sticks, bats, BBs, pellets, and even up to 44-caliber bullets!

LED Tunnel and Subway Lighting High Power Led Tunnel and SubWay Light:
Revolutionary Photometric Design-The world’s first dedicated optical system(rectangular beam focusing lens): Reasonable control of the light distribution, spot rectangular bean pattern ,and ensure an ideal uniformity of brightness on the road surface, eliminate the glare and keep the LED lighting efficiency on a high level, no light pollution

High Power LED Tunnel Light PDFiles/Instruction Manual for Tunnel Light.pdf

High Power LED Street Light:High Power Led Streetlight
Designed to eliminate glare, light trespass, and sky glow, the LED street lights only shine light at ground level. Multiple colors Temperature from 3000K to 7500K are available, suitable for different area and situation. The Power varies from from small security yard, to Major road. The lamp applies high power LED. Fine cooling system applied. The average life time of the system can be high up to 50,000 hours, lighting 10-11 hours a day, the light can be used for more than 11 years.
How to Retrofit Street Lights with LED by IQLED

IQUPs.com Explosion proof UPS backup lighting systems: Explosion proof Lights, Explosion proof LED Lights, Explosion proof Lights, Solar Explosion proof LED Lights, Solar LED Explosionproof Lights, LED Explosionproof Lights, Explosion proof LED Lights, LED Explosion proof Lights, Explosion proof Fluorescent Lights, Explosionproof Steady-On Lights, Explosion proof Steady On Lights

IQUPS.com

IQ LED Street Lighting 488500
Easy to retrofit LED streetlights can easily retrofit existing metal halide, high pressure sodium and mercury vapor luminaries.
Click Here for More information!

LED Street Lighting High Power LED Street Light Manufacturer and Exporter of LED Street Lights

Manufacturer: IQLED Lighting
Rugged LED OUTDOOR LUMINAIRES Replaces HPS up to 320W - Equal to HPS Lumen 13,600!

Bulletproof/Vandalism Proof Lighting Fixtures available.
LED fixture rated to withstand mechanical vibration per MIL-STD 883, test method 2007, using three 4-minute cycles along x, y and z axis, at a force of 2.5 Gs, with a frequency sweep from 2 Hz to 120 Hz.
Hurricane Proof LED Lighting
OkSolar solar LED Parks Lighting Change This type of unsafe setup for More information Lcick Here!
Seismic Restraint Solar LED

ABC Technical Information:

Technical LED's LED Color Chart.

Explosion Proof LED Fixtures 12VDC, 24VDC, 120VAC 240VAC 277VAC , 50 - 60 hertz Available in pendant, ceiling, stanchion and bracket mounts.
UL Listed for Standard 844
IQLED has been making Explosion proof Lighting systems
UL Listed for Standard 844 IQLED has been making Explosion proof Lighting systems

Construction Features Lamp compartment is factory sealed from wiring chamber, eliminating on-the-job sealing. Inspection hole provides easily accessible splice space. There is nothing to hold while splicing to line. Set screw to stem keeps fixture from turning during relamping. Three close-up plugs furnished with four hole junction box. Mounting lugs are standard.

Lamp: LED 400+ Super Bright LED's
Housings: Heavy cast aluminum. Unit withstands 1490 lbs. per square inch hydrostatic pressure during UL testing
Wiring: Wiring is factory sealed. Inspection hole provides easy access to splice compartment
Globe: Impact and heat resistant clear prismatic design affords excellent light control
Finish: Silver Gray Epoxy powder coat
Reflectors: Heavy gauge aluminum with highly reflective white acrylic finish
Socket: Medium base glazed porcelain. Leads pass through sealing compound that separates lamp chamber from wiring compartment. Heavy gauge nickel plated copper components. Spring loaded center contact

Petroleum Station Canopies LED Lighting - Gas Station Explosion Proof LED Canopies LED Fixtures Save on energy consumption and maintenance costs, with easy to install HighFlux LEDs that provide bright, uniform light distribution. Save on energy consumption and maintenance costs, with easy to install HighFlux LEDs that provide bright, uniform light distribution.

Petroleum Station Canopies LED Lighting

Solar Powered LED Lighting

These units can be used for: Area lighting, Billboards lighting, Dock lights, Park lighting, Parking lot lighting, Parkway lighting, walkway lighting, Street lighting, Transit Lighting, Outdoor area lighting

Select the right optic for the right application Contact Us Today!

Hurricane Proof LED Lighting - Seismic Restraint LED

“The installation of the post-top fixture LED retrofit allowed some colleges to utilize their existing light fixtures to save energy and improve light quality on their campus without sacrificing safety and aesthetics” College can save $16,000/year with IQLED LED retrofit lamps The installation of 100 post-top fixture LED retrofit kits will save energy and enhance light quality at College campus. LED High-Power Bulbs for Decorative Post-Top-Style Street & Walkway Luminaires Post Top Style by IQLED.com Manufacturer and Exporter

Airport Lighting Fixtures

Airport Lighting Parts

Solar Powered Airport Lighting Obstruction, Taxiway

POLE SELECTION GUIDELINES WIND SPEED

The UNIVERSAL HAND HOLE COVER (OkU-Cover) is a security cover for light poles. The product secures from outside the pole with a stainless steel strap and a penta head security bolt.

Item# 160723

Click Here for Div. 2 Hazardous Location and Explosion proof
Hazardous Location Emergency-Exit Backup

Hazardous Location Lighting Accessories

Hazardous Location Lighting Fixtures

Vapor Tight Fixtures

Explosion Proof Ceiling Mount Fixture

Solar Powered LED Lighting with Protection against gun shot and vandalism LED Outdoor Luminaires

We have designed complete Solar Powered Lighting packages of Vandalism Protection Lighting Shields, for several applications, including Solar Roadway Lighting and Solar Outdoor Area Lighting for civil and military applications

consists of a complete line of protective shields for Cobra Head street lighting fixtures. This patented* shield incorporates leading edge technology to provide maximum ballistics resistance. Installation and maintenance are a snap. The shield is primarily constructed of dual layer polycarbonate sheets which are UV stabilized.

Designed to stop small arms fire .22 to .44 caliber
Simple one bolt installation
Excellent stoppage from 9mm handguns, the most popular vandalism hand gun on the streets
Will withstand most field vandalism
Compact, eye appealing design
Does not interfere with routine maintenance
Mounts on all standard pole arms

Area Lighting Vandal Shields will withstand the fire of a 9mm handgun - the most popular vandalism handgun on the street today. They are constructed with state-of-the-art technology for optimal ballistic resistance.

Easy Installation and Maintenance
Superior Protection, made from dual layers of polycarbonate glazing sheets
Designed to stop small arms fire (.22 - .44 caliber)
Excellent stoppage from 9mm handguns, the most popular\
vandalism handgun on the streets
Superior long term protection against vandalism & accidental damage

Easy to retrofit IQ LED streetlights can easily retrofit existing metal halide, high pressure sodium and mercury vapor luminaries.

Your next schedule IQLED maintenance will be in 8 to 10 years!

with our IQ Retrofit Lamps

IQLED Unlike bulb streetlights, IQLED lighting modules produce very intense light in tightly control IQLED directions. There is no longer a need for reflectors or cut-off shields to minimize light pollution and trespass. With IQLED energy usage less than 20% and lifespan more than seven times that of conventional streetlights, payback occurs very early in a long life cycle. One specific advantage of LEDs is that they produce directional light. This gives you more control over what you light (i.e. the street) and what you don't (the night sky), reducing light pollution and wasted energy. LED has significantly better lumen maintenance LED fixture typically doesn’t need relamping to 70,000 hours. if you are looking for LED Street Lights, LED Streetlights, LED Street Lamps, Retrofit LED Street Lights, Solar LED Street Lights, LED Traffic Lights, LED Traffic Signals, Retrofit LED Modules, High Power LED Bulbs, LED Lamps, LED Spot Lamps or some other customized LED Lighting products, Please do not hesitate to contact NOW! The crisp white light produced by LEDs can significantly enhance nighttime visibility compared with the cloudy orange light produced by high pressure sodium.

Solar Powered Explosionproof Lights, Explosionproof light, Explosion proof light, Explosionproof Strobes, Explosion proof Strobes, Explosionproof Steady-On Lights, explosion proof light fixture is ideal for wet/damp or hazardous ... Explosion proof fixture for ceiling mounting

Solid State Lighting Edison Screw Based LED Lamps, E26 EDISON SCREW BASED LED LAMP 120VAC, 120 VAC LED Bulbs, 230 VAC LED Bulbs, Solid State Lighting Edison Screw Based LED Lamps, light emitting diode lights, LED billboard sign lights, commercial LED fixtures, fixture retrofitting, LED post lights, phone booth lights, bus stop lighting, non-explosive lights, temperature tolerant lights, LED Illumination, LED lighting, Traffic lights, traffic lighting, Traffic control lights

5W high power MR16, High Power LED bulb, LED E27 Spotlight, MR16 and E27 with Luxeon LEDs, PAR30 LED Lamp, GU10 Spotlight, 5W MR16 GX5.3 T-TYPE Spotlight

01681000

01540

488300

01420

01503

01440

488500

No Bulbs! No Ballasts! No Starters! Its Ok NO Problems

With IQLED, you are limited only by Your imagination in the use or design of your Lighting fixtures.

We design, manufacture and deliver state of the art, LED Lighting Solutions IQLED.com Green Lighting solutions for indoor and outdoor uses, in both ac and dc voltages for: residential, commercial, retail, industrial, municipal, government, medical, military, transit, aeronautic/space, and for mission critical industries. If you are not able find what you are looking for, we can custom design and produce it for a reasonable cost. Contact us with your ideas or lighting requirements Today!.

Flex Strips: Flexible, LED strips with customizable LED options for architectural installations.

Retrofit Bulbs: Screw in ac/dc LED retrofits bulbs with customizable LED and lens configurations.

Streetlight Retrofits: Shoebox, drop down, acorn and cobra head LED streetlight retrofit solutions.

IQLED Green Lighting solutions environmentally friendly, outdoor LED streetlighting has arrived. Designed to be efficient, low glare and Dark Sky compliant, our full line of IES certified LED streetlights can easily retrofit existing metal halide, high pressure sodium and mercury vapor luminaries.

Nontoxic, RoHS compliant, made with environmental friendly materials, we fabricate LED streetlight retrofits for box style, cobra head, acorn and dropdown or entirely custom LED streetlights based on specifications, requirements or aesthetics.

Our IQLED Streetlight retrofits can be installed with not effort, while still utilizing existing power, housing and lens. Built using segmented construction, each LED Streetlight, consists of individual panels; combating vandalism and enabling easy access to replace damaged components. IQLED designed to operate in extreme conditions, our LED streetlights don’t flicker or hum, require no warm up time and can operate in -40 to +180 degrees Fahrenheit.

Will Provide substantial security lighting for your parking lot, garage or workspace; aim the light where it is needed, curb high utility and maintenance costs and avoid polluting the night sky with excess light, with our full line of certified, low voltage, LED Streetlighting retrofits. Download lumen ratings and IES certification for our LED Streetlight retrofits:

LED lights use half the energy (or less) and last longer than conventional bulbs, resulting in big savings and short payback periods. One specific advantage of LEDs is that they produce directional light. This gives you more control over what we light (i.e. the street) and what we don't (the night sky), reducing light pollution and wasted energy.

Saving energy and money. The new IQLED lens fixtures use less energy, helping to keep operating costs down. After three years, The City will regain the cost of installing the new fixtures from energy and maintenance savings.

Reducing greenhouse gas emissions. Using less electricity reduces the emissions produced by gas and coal-burning generators. When the IQLED Streetlights project is completed, carbon dioxide emissions will be reduced.

Reducing glare to increase visibility. Glare from street lights is significantly reduced with the new IQ LED's street-light fixtures, increasing visibility by directing light onto the roadway and preventing it from shining into the eyes of motorists.

Reduce excessive lighting and light pollution. New ways of designing and providing street lighting have been developed in the last several years.

Maintaining a safe level of lighting. Street lighting on residential and collector roads will continue to meet minimum Illuminating Engineering Society (IES) guidelines.

If your City is committed to savings and reduce the level of light pollution by using the most efficient IQ LED street-light fixtures and employing the latest design methods.

New series of IQLED lamps 'Brighter than HID' linear lighting as well as TYPE III roadway lamps that meet IES specs from 35' mounting heights!

IQLED Modular LED Luminaire systems. allow you to design your own Luminaire (Fixture)

Weatherproof for coastal climates
Vibration resistant for tunnels and bridges
Withstand 160 MPH winds
LED fixture rated to withstand mechanical vibration per MIL-STD 883, test method 2007, using three 4-minute cycles along x, y and z axis, at a force of 2.5 Gs, with a frequency sweep from 2 Hz to 120 Hz.
Manufactures in accordance with MIL Specs, ISO 9001:2000, ROHS Compliant parts Quality Standards.
Solid-State long life “hi-flux/hi-power ”IQLED's.
Shock and vibration resistant.
Eliminate unsafe hazardous disposal.
Eliminate “cold-start” problems; no ballast.
Rugged waterproof design.
Better visibility with excellent Lumen efficiency.
Environmentally friendly.
Substantial energy & maintenance savings.
Expected life > 50K + hours; 3 year warranty.
Approximate 3-year payback.
Significant Operational Savings- Energy & Maintenance.
High color rendition - objects appear more natural than with bulb lighting
More than 5 times longer life than conventional
High reliability and minimal maintenance
The modules are supplied with glass replacement panel, lens, power supply and terminations/leads. Expected product life is 10 years with an approximate 3-year payback period, depending upon local energy & maintenance cost savings.
How to Retrofit Street Lights with LED by IQLED
High Power LED Street Light Manufacturer and Exporter of LED Street Lights
Replacement of Conventional Light Sources by LED Streetlight, LED Street Light IQLED.com
OkSolar solar LED Parks Lighting Change This type of unsafe setup for More information Lcick Here!

Contact us today!

Specifications Series

Operating Voltage	90 to 265 VAC, 47 to 63 Hz
Wattage	48-180 Watts
Power Factor	>0.90
Intensity Regulation	Better than 10%
Color Temperature	5,000 to 5,500 °K
CRI	65 (typical)
Lumens	na
Operating Temp	-35°C to 60°C
Storage Temp.	-40°C to 85°C
Humidity	0 –99%
Electrical Wire	3 x 24 inch, 18 AWG leads, Female slip terminal
Size	Emitting area 8.25”x 8.25”
IQLED's	one-watt white Hi-Flux

Watts	Replaces HPS	Equal to HPS Lumen Efficiency of
48W	75W	3,300
60W	125W	4,400
80W	150w	6,000
100W	175W	7,600
125W	200W	9,400
140W	250W	10,600
180W	320W	13,800

Note: HPS Wattages do not include ballast wattages; only the lamp ratings.

Brightness Estimated equivalency:

1000mcd = 1 Lumen (.05-1.5 lumen)

* Note: HPS Wattages do not include ballast wattages; only the lamp ratings.
** Note: IQLED Luminaries produce high quality white light @ 5500K color temperature which greatly enhances the nighttime visibility, color rendition & Scotopic (nighttime) visibility of the human eye.

Note: Meets IES minimum requirements for roadway lighting.

IQLED Series Luminaries utilize hi-power white IQLED's with superior thermal management design. These extremely durable fixtures are waterproof and designed for multiple applications including indoor and outdoor.

125Watts

100,000 Hours LED Life Expectancy
Years	16	22	45	54	68	91	136
Operating Hours per day	7	6	5	4	3	2	1

eco IQLED Retrofit to MR16 LED based products (B22, GU10) high power LED Light Bulbs clear bright and white light. Led Spot lights, 3 1w MR16 high power led lamp, 1, 3 and 5 watt LED Luxeon Bulbs, gu10 bulbs, e27 bulbs Optimized thermal management Selectable beam angles Full range of light output colors Low heat No UV LED Luxeon Bulbs, 1/3/5 Watt, MR16/GU10/E27 Base Application: This LED spot light is widely used in Airport signaling, Street lighting, advertise lighting, mall, hotel, club, disco hall, casino, coffee bar, bank, meeting room, exhibition, walkway, show window, navigation signal etc. High Power Led Tunnel and SubWay Light: Revolutionary Photometric Design-The world’s first dedicated optical system(rectangular beam focusing lens): Reasonable control of the light distribution, spot rectangular bean pattern ,and ensure an ideal uniformity of brightness on the road surface, eliminate the glare and keep the LED lighting efficiency on a high level, no light pollution LED Tunnel Light Tremendous Energy Saving: Used the ultra high power, high brightness LED light source ,together with the high power efficiency power supply, which can save energy 50%-80% than the conventional sodium and mercury lamp Intelligent current control, achieve the precision constant current: Each LED module can implement intelligent current control, whatever power network how to wave, it is able to achieve the precision constant current, ensure the LED can work under the secure curren No Strobe Flashing: Eliminate the visual fatigue which caused by the strobe lights of the traditional tunnel lamps. Perfect Support intelligent control: such as combine Tunnel lighting starts shortly as trait(<2 seconds), Adopt the newest technology of tunnel lighting intelligent control, when no vehicles pass tunnel, It can put out most of lamps, when vehicles pass tunnel entrance at within 500m area, It can start lighting automatically. So It has solved the problem of smaller tunnel traffic which no vehicles pass the tunnel will waste a great deal of electric power sources. Supply a new idea “establish saving society” to city road management Petroleum Station Canopies LED Lighting - Gas Station Explosion Proof LED Canopies LED Fixtures Save on energy consumption and maintenance costs, with easy to install HighFlux LEDs that provide bright, uniform light distribution. Save on energy consumption and maintenance costs, with easy to install HighFlux LEDs that provide bright, uniform light distribution.
Night sky wildlife compliant bulbs IQLED Illumination “The installation of the post-top fixture LED retrofit allowed some colleges to utilize their existing light fixtures to save energy and improve light quality on their campus without sacrificing safety and aesthetics” College can save $16,000/year with IQLED LED retrofit lamps The installation of 100 post-top fixture LED retrofit kits will save energy and enhance light quality at College campus. LED High-Power Bulbs for Decorative Post-Top-Style Street & Walkway Luminaires Post Top Style by IQLED.com Manufacturer and Exporter
High Power LED Street Light: High Power Led Streetlight Designed to eliminate glare, light trespass, and sky glow, the LED street lights only shine light at ground level. Multiple colors Temperature from 3000K to 7500K are available, suitable for different area and situation. The Power varies from from small security yard, to Major road. The lamp applies high power LED. Fine cooling system applied. The average life time of the system can be high up to 50,000 hours, lighting 10-11 hours a day, the light can be used for more than 11 years. Parking Garage - Municipal garages Item#01450	Item# 01460
Note the brightness of IQLED Lamps compared to Incandescent Lamps!

Locking Thermal Photo control, Voltage Rating 120 to 277 Volts 5u793

Item#0167100 Fixture Roadway 400 W
Roadway Lighting Fixture, Lamp Watts 400, High Pressure Sodium, Voltage 120/208/240/277, Suggested Lamp Stock No., Socket Mogul Base, Lens Drop Glass, Light Distribution Type III, Housing Die Cast Aluminum, Arm Mount Bolt On Mast, Finish Gray Electrocoat, Gasket Fiber, For Lighting Residential Streets, Storage Areas, Parking Lots, Campuses and Parks, Height 14.41 In, Width 15.12 In, Depth 31.81 In, Listing/Certification IP55 Rated, Includes Photocell Socket (Photocell Not Included)

Item#0167050 Fixture Roadway 250 W
Roadway Lighting Fixture, Lamp Watts 250, High Pressure Sodium, Voltage 120/208/240/277, Suggested Lamp Stock No. , Socket Mogul Base, Lens Drop Glass, Light Distribution Type III, Housing Die Cast Aluminum, Arm Mount Bolt On Mast, Finish Gray Electrocoat, Gasket Fiber, For Lighting Residential Streets, Storage Areas, Parking Lots, Campuses and Parks, Height 10.63 In, Width 13.25 In, Depth 26.25 In, Listing/Certification IP55 Rated, Includes Photocell Socket (Photocell Not Included)

Item#0167200 Fixture Roadway 150 W
Roadway Lighting Fixture, Lamp Watts 150, High Pressure Sodium, Voltage 120, Suggested Lamp Stock No. , Socket Mogul Base, Lens Drop Acrylic, Light Distribution Type II, Housing Die Cast Aluminum, Arm Mount Bolt On Mast, Finish Gray Electrocoat, Gasket Fiber, For Lighting Residential Streets, Storage Areas, Parking Lots, Campuses and Parks, Height 10.63 In, Width 13.25 In, Depth 26.25 In, Listing/Certification IP55 Rated, Includes Photocell Socket (Photocell Not Included)

Item#0167150 Fixture Roadway 400 W
Roadway Lighting Fixture, Lamp Watts 400, Metal Halide, Voltage 120/208/240/277, Suggested Lamp Stock No., Socket Mogul Base, Lens Drop Glass, Light Distribution Type III, Housing Die Cast Aluminum, Arm Mount Bolt On Mast, Finish Gray Electrocoat, Gasket Fiber, For Lighting Residential Streets, Storage Areas, Parking Lots, Campuses and Parks, Height 14.41 In, Width 15.12 In, Depth 31.81 In, Listing/Certification IP55 Rated, Includes Photocell Socket (Photocell Not Included)

Item#0167300 Fixture Roadway 100w
Roadway Fixtures, High Pressure Sodium, Lamp Watts 100, 120 Volts, Suggested Lamp Stock No , Socket Mogul, Lens Drop Acrylic, Light Distribution Type II, Housing Die-Cast Aluminum, Finish Painted Gray, Gasket, For Roadways, Residential Streets, Storage Areas, Parking Lots, Campuses, Parks, Height 10.1 In, Width 13 In, Depth 27 In

Item#0167250 Fixture Roadway 250w
Roadway Fixtures, High Pressure Sodium, Lamp Watts 250, Multi-tap wired 120 Volts, Suggested Lamp Stock No , Socket Mogul, Lens Drop Glass, Light Distribution Type III, Housing Die-Cast Aluminum, Finish Painted Gray, Gasket, For Roadways, Residential Streets, Storage Areas, Parking Lots, Campuses, Parks, Height 10.1 In, Width 13 In, Depth 27 In

Item#0167400 Fixture Roadway 150w
Roadway Fixtures, High Pressure Sodium, Lamp Watts 150, 120 Volts, Suggested Lamp Stock No, Socket Mogul, Lens Drop Acrylic, Light Distribution Type II, Housing Die-Cast Aluminum, Finish Painted Gray, Gasket, For Roadways, Residential Streets, Storage Areas, Parking Lots, Campuses, Parks, Height 10.1 In, Width 13 In, Depth 27 In

Item#0167350 Fixture Roadway 250 W
Roadway Lighting Fixture, Lamp Watts 250, High Pressure Sodium, Voltage 120/208/240/277, Suggested Lamp Stock No. , Socket Mogul Base, Lens Flat Glass, Light Distribution Type III, Housing Die Cast Aluminum, Arm Mount Bolt On Mast, Finish Gray Electrocoat, Gasket Fiber, For Lighting Residential Streets, Storage Areas, Parking Lots, Campuses and Parks, Height 5.75 In, Width 13.25 In, Depth 26.25 In, Listing/Certification IP55 Rated, Includes Photocell Socket (Photocell Not Included)

Item#0167500 Fixture Roadway 150 W
Roadway Lighting Fixture, Lamp Watts 150, High Pressure Sodium, Voltage 120, Suggested Lamp Stock No. , Socket Mogul Base, Lens Flat Glass, Light Distribution Type III, Housing Die Cast Aluminum, Arm Mount Bolt On Mast, Finish Gray Electrocoat, Gasket Fiber, For Lighting Residential Streets, Storage Areas, Parking Lots, Campuses and Parks, Height 5.75 In, Width 13.25 In, Depth 26.25 In, Listing/Certification IP55 Rated, Includes Photocell Socket (Photocell Not Included)

Item#0167450 Fixture Roadway 400 W
Roadway Lighting Fixture, Lamp Watts 400, Metal Halide, Voltage 120/208/240/277, Suggested Lamp Stock No., Socket Mogul Base, Lens Sag Glass, Light Distribution Type III, Housing Die Cast Aluminum, Arm Mount Bolt On Mast, Finish Gray Electrocoat, Gasket Fiber, For Lighting Residential Streets, Storage Areas, Parking Lots, Campuses and Parks, Height 8.32 In, Width 15.12 In, Depth 31.81 In, Listing/Certification IP55 Rated, Includes Photocell Socket (Photocell Not Included)

Item#0167600 Fixture Roadway 150w
Roadway Fixtures, Compact, High Pressure Sodium, Lamp Watts 150, 120 Volts, Suggested Lamp Stock No , Socket Mogul, Lens Drop Acrylic, Light Distribution Type II, Housing Die-Cast Aluminum, Finish Painted Gray, Gasket, For Roadways, Residential Streets, Storage Areas, Parking Lots, Campuses, Parks, Height 6.8 In, Width 12.8 In, Depth 21 In

Item#0167550 Fixture Roadway 400 W
Roadway Lighting Fixture, Lamp Watts 400, High Pressure Sodium, Voltage 120/208/240/277, Suggested Lamp Stock No. , Socket Mogul Base, Lens Flat Glass, Light Distribution Type II, Housing Die Cast Aluminum, Arm Mount Bolt On Mast, Finish Gray Electrocoat, Gasket Fiber, For Lighting Residential Streets, Storage Areas, Parking Lots, Campuses and Parks, Height 8.32 In, Width 15.12 In, Depth 31.81 In, Listing/Certification IP55 Rated, Includes Photocell Socket (Photocell Not Included)

160710

160709

160710

160709

1459

Teardrop Light

1460

1467

Post Top Light

1462

Square Poles

Marking a breakthrough in light-pole safety and endurance, the Crown-Weld is many times stronger than the traditional-design pole. It presents a dramatic improvement in pole fatigue resistance and yield strength.

The Crown-Weld features a base with four formed triangular sections to which the pole shaft is welded on all four sides. When loading, such as the kind of pressure a strong gust of wind would exert, is applied to the pole at stresses above the endurance limit, the Crown-Weld proves vastly superior, with a 50 percent increase in EPA values.

Complete line of steel and aluminum poles that provide outstanding strength and reliability. Crown-Weld steel poles set the new standard for outstanding strength and reliability. These non-tapered poles are available in 3-, 4-, 5- or 6-inch square ranging from 10 through 30 feet in length

The poles come with a reinforced hand hole that is welded to the shaft. The steel hand-hole cover is attached with two high-strength fasteners. The grounding lug meets UL and NEC requirements for electrical ground bonding. Lighting poles meet or exceed NEC requirements.

Round Tapered Poles

Round Tapered Poles combine their graceful, distinctive appearance with quality construction. They are available in lengths of 25, 30, 35, 40, 45 and 50 feet. Fixture mounting is accomplished by attaching the fixture, via the Round External Mount Vertical or Horizontal Tenon (PB/PT Series), to a 2-inch schedule 80 pipe that is peripherally welded to the top of the shaft.

Round Tapered Poles come standard with a bronze polyester powder finish that carries a one-year warranty. Each pole is shipped complete, with galvanized anchor bolts, Masonite mounting template and base cover. The two-piece steel base cover is held together by two high-strength fasteners.

IQLED.com Night sky wildlife compliant bulbs IQLED Illumination Night sky wildlife compliant bulbs IQLED Illumination

Roadway Fixtures