|
We are leader specializing in a wide range of commercial, industrial, data and
telecommunication technology applications, sets the standard of excellence for
enclosures worldwide contact Us with your enclosures cabinets needs at Sales
outdoor waterproof enclosures, nema cabinets, electrical box, fan, cooling
kits, equipment racks, outdoor shelter, heating, air conditioning, racking
cabinets, industrial enclosures, networking racks, aluminum products
8" Rear Apron
- Shields rear connections
& fan form the rain pre-drilled 3-cut outs support: 2-type N
access holes
or UHF chassis mount
connector's 1-7 pin weatherproof connector , 1-5" mtg. hole for
exhaust fan.
(Removeable plates cover cut outs when not in use)
Finish
- Cream, textured, powder baked on paint
Rails-
Two standard, anodyne coated, EIA 19"
Door -
Front door secured with non-intrusion lock
Seals
- Neoprene slotted gasket seals top cover
Aluminum filled 13/16" gasket seal door
|
The OkPOD3020 is a compact totally
weatherproof (NEMA 4) outdoor enclosure. This new compact enclosure
offers 20" of useable depth & accommodates up to 30 vertical inches
of 19" rack space. Pre-drilled into the back wall and covered with a
3" x 8" apron are four connector hole patterns (cut outs, 2
for RF & 1 for power & for exhaust fan). Each of the four connector
cut outs comes with it's own removable access plate. These access
plates may be left in place if not needed or they may be
removed. This design makes this unit very portable. Once you,
install the three connectors, connect their associated wiring to
your unit & rack mount your unit, you can close the door and lock
it. From then on the RF and power will be accessible through the
three connectors in the rear of the OkPOD3020. A 5" fan may be
mounted up inside the 8" apron if ventilation is needed. The
OkPOD3020 can be wall, floor, or pole mounted.
|
|
Weights: |
61 Lbs. assembled (EST.`) |
|
Doors: |
One - secured with non-intrusion lock
Two keys supplied |
|
Door Seal: |
13/16" aluminum filled gasket |
|
Material: |
.125 ALUMIFLEX / RF properties:
Non-ferrous finish: Gray, Textured, powder baked on paint. |
|
Top Cover Seal: |
Neoprene slotted gasket |
|
Exterior Screws: |
Stainless with NEMA washers & nylon
locking nuts |
|
Rails: |
Two standard (.125 Alumiflex,
material)
Anodyne coated
19" racking holes tapped to 10 x 32 threads
Note: Rails come pre-mounted, which allows
your equipment's handles room to protrude out in front a distance up
to 1 1/4 inches
(if this is acceptable)
Or, if desired, rails can be mounted at any depth. (Customer drills
four new mounting holes & mounts rails with the supplied extra
screws & lock nuts)
|
|
Spacing: |
19" EIA STANDARD |
|
Useable Height: |
30 inches |
|
Useable Depth: |
20 1/2" minimum / 21" maximum |
|
Width: |
21 7/8 inches |
|
Height: |
30 inches |
|
EXTERIOR
CABINET DIMENSIONS |
|
Main Body: |
Width: 22 1/4 inches
Height: 30 3/4 inches
Depth: 25 1/4 inches |
|
Door: |
Width: 23 1/8 inches
Height: 31 1/8 inches
Depth: 1 3/4 inches |
|
|
Width: 23 2/8 inches
Height: 31 2/8 inches
Depth: 25 1/2 inches |
|
INSIDE
CLEARANCE - LESS RAILS |
|
Width: |
21 7/8 inches |
|
Height: |
30 inches |
|
Depth: |
22 1/4 inches |
|
REAR POWER
CONNECTOR HOLE |
|
Hole Size: |
One .858" diameter hole with two
.142" mtg holes / spaced 1.22" apart |
|
Description: |
Supports one male 7 pin power
connector
( Allied part # T-3106-000 (weatherproof - male) mates with female 7
pin power connector
( Allied Part # T-6482-000 (weatherproof - female)) |
|
Location: |
Under the rear apron, in the center
of the rear panel |
|
Hole Size: |
Two .641 diameter holes
Each with four .125" mtg holes / spaced .718" sq. |
|
Description: |
Supports two chassi mount type N or
UHF con's |
|
Location: |
Both holes are located under the rear
apron, one on the left side & one on the right side of the rear
panel. |
|
NEMA: |
CLASS: 250
TYPE: 4 |
|
Paint Tested: |
500 Hour salt spray
500 Hour immersion |
|
PERIOD: |
|
FOUR YEARS - UNCONDITIONAL |
|
VENTILATION |
|
Air intake: |
12 vent
louvers (bottom plate) covered with aluminum screen and removable
foam filter |
|
Air outlet: |
2 - 5"
exhaust fan hole ( with removable plate ) |
|
OkSCR-432: |
Four 10 x 32 rail screws |
|
OkR-2-10: |
Two extra 10" rails & mtg. hdw. |
|
OkR-2-30: |
Two extra 30" rails & mtg. hdw. |
|
|
The 8" wide by 22 1/4" hang down apron, runs
horizontally & is located at the top of the back panel. The matching
1 1/2" by 22 1/4" wide bent up mounting plate, runs
horizontally & is located at the bottom of the back panel.
Customer drills the needed mounting holes into the 3" hang down
apron & 1 1/2" bent up mounting plate. |
|
|
|
The OkPOD3020
is shipped fully assembled, via UPS |
OkSolar.com Affiliate
 Note:
To view the above PDF documents, you will need the
free Adobe Acrobat Reader
Batteries Enclosures for commercial, industrial,
military applications, battery enclosures, battery cabinets, cabinets, battery
cabinets, batteries enclosures, batteries cabinets, enclosures, Enclosures
commercial, enclosures industrial, enclosures data and telecommunication
technology applications !
|
