OkSolar News - A Piece of Cake for the OEM Electronics Industry

Ultimate, Powerful, Digital System

New Communications Devices from GeneralCommunications.com

What is this "frequency-hopping"?

Adott: Wireless Sensors

Point Sensor IR Counter
Battery Operated IR Sensors with an Integrated RF Transmitter
The Point Six IR Point Sensor is a battery operated infrared beam interruption sensor with a 418 MHz radio transmitter. The sensor consists of two parts; the IR transmitter and the IR receiver. The IR receiver has an integrated 6-digit LCD counter and a radio transmitter for truly wireless installation and operation. The IR transmitter produces 16 pulses of IR each second across a distance of up to 60 feet in low power mode and 100 feet in high power mode More Information Click Here

Main Features 32-Bit unique ID with 24-bit Digital Counter, digital input status Switch for installation and service mode indication Up to 600-foot range Transmits immediately on status change Up to 100 transmitters can coexist Battery lasts from 5 to 10 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Complies with part 15 of the FCC rules Water resistant coating on PCB CRC-16 checked Status, ID and counter data Internal Loop antenna Low Cost Description: The Point Sensor Magnetic Door wireless transmitter is a battery operated digital counter sensor with a microprocessor controlled 418 MHz. FCC certified radio transmitter. The Point Sensor Magnetic Door has an on board time of day clock that allows it to spend most of the time in a low power quiescent state. At predetermined time intervals the clock will wake up the onboard microprocessor. Unique serial number information is read from a Dallas Semiconductor 1-wire digital device, counter data is read from a 24-bit internal counter register. This information is combined with a CRC-16 error check and transmitted in a very short data packet that results in a transmitter on time of only 15 milliseconds. This architecture allows the Point Sensor Magnetic Door to consume very little energy and a battery life of 5 to 10 year results. The Point Sensor Magnetic Door electronics are coated with a conformal material that provides a moisture barrier against condensation. Submersion in water is not recommended. A pushbutton switch in the ABS cover allows the user to activate the service mode. The service switch has three functions: 1)The Point Sensor Magnetic Door is shipped with the transmitter turned off, anytime the Point Sensor Magnetic Door is to be shipped the transmitter should be turned off or placed in a shielded container to prevent interference. Start the Point Sensor Magnetic Door by a momentarily push of the service switch (you will feel the button click) the Point Sensor Magnetic Door is started. 2) The service switch is used as an aid to installation, when the service switch is pushed a data transmission occurs immediately and a special mark is introduced in the ID field of the transmitted data packet to indicate which sensor is in service or installation. 3)The service switch is used to put the Point Sensor Magnetic Door in a quiescent mode (no transmissions and very low power consumption), this is the state the Point Sensor Magnetic Door is in when you receive it from the manufacturer. Push and hold the service switch for 5 seconds or more to enter this powered down state.

We provide: industrial wireless controls, industrial radio control, industrial controls wireless, industrial radio control, industrial radio remote control, industrial wireless control, remote controls, belly box transmitter, wireless remote control, wireless controls, radio controls, radio remote controls, crane control, remote crane control, crane remote control, monorail remote control, overhead crane control, concrete pump control, conveyor remote control, conveyor control, remote winch control, wireless winch control, remote boom control, belly box transmitter, remote relay control, relay remote control

GeneralCommunications.com  has a Solution for every application. Contact Us at sales@generalcommunications.com

Communicating - Alerting - Warning!  Audible signaling, Visual Signaling, Wireless. A signal for every signal need. From cranes and conveyors to safety and security, signals that can be both seen and heard. Point to Point or Point to Multipoint monitor and control level, flow, pressure, temperature, alarms, etc., while eliminating costs for cable, conduit, trenching and boring. We help you Communicate and Move your Data point to Point multipoint Automation signaling works best when you partner with an experienced source, one with a track record of product innovation and technical leadership. GC signals come with innovative features that meet all your signaling applications needs. From simple horns and bells to demanding factory automation signaling utilizing your PLC or Devicenet network, wireless, powered by Solar and Fuel Cells, GC provides complete factory solutions. Find out what makes signaling sense to you! Applications include: Products for material handling applications like Underground Mining, Processing & Airport Transportation industries, Military Applications, Whether your application requires SPEED MONITORING, REMOTE CONTROLS, Security environments we can OEM at your specs, Remote areas Control and Visualization. Visual and Airport Suppliers Find Runway lights, runway lighting, Runway End Identifier Lights, Heliport Lighting/Navigational Aids, and Obstruction Lights, Transportation, Airports, Operations and Maintenance, Supplies and Equipment. Signal Solutions for industrial, commercial, institutional and security applications. Everything you need to satisfy your customer for OSHA, ADA or Process control signal requirements.

Wireless RF sensors Temperature, Counters, Vibration, ID, Pressure, and More... With an emphasis on modularity and compatibility, The GCS Family is ideally suited for a broad range of applications from basic telemetry to custom engineered wireless networking solutions. A complete family of wireless RF sensors, transmitters, loggers, repeaters, receivers and servers spanning the 418MHz. to 2.4GHz frequency range. With an emphasis on modularity and compatibility, The Point Family is ideally suited for a broad range of applications from basic telemetry to custom engineered wireless networking solutions More info

GeneralCommunications Communicating - Alerting - Warning! Audible signaling, Visual Signaling, Wireless.   Portable Radio Remote Controls: A signal for every signal need. Radio Remote Control for cranes, locomotives, material handling equipment, mining machinery, mobile equipment, shiploaders, agricultural machinery, and virtually any equipment where the operator can be moved to a safer, more efficient location signals that can be both seen and heard. Automation signaling works best when you partner with an experienced source, one with a track record of product innovation and technical leadership. GC signals come with innovative features that meet all your signaling applications needs. From simple horns and bells to demanding factory automation signaling utilizing your PLC or Device net network, wireless, powered by Solar and Fuel Cells, GC provides complete factory solutions. Find out what makes signaling sense to you!  Remote Controls Applications include: Products for material handling applications like Underground Mining, Processing & Airport Transportation industries, Military Applications, Whether your application requires SPEED MONITORING, REMOTE CONTROLS, Security environments we can OEM at your specs, Remote areas Control and Visualization. Visual and Airport Suppliers Find Runway lights, runway lighting, Runway End Identifier Lights, Heliport Lighting/Navigational Aids, and Obstruction Lights, Transportation, Airports, Operations and Maintenance, Supplies and Equipment. Signal Solutions for industrial, commercial, institutional and security applications. Everything you need to satisfy your customer for OSHA, ADA or Process control signal requirements

SCADA Supervisory Control And Data Acquisition. SCADA may be called Human-Machine Interface (HMI) in Europe. RF Wireless Solutions, RF, Wireless Data Collection, Industrial RF solutions, SCADA, wireless SCADA, RF SCADA monitoring, wireless transceivers Data from and control signals to pipes, valves and pumps can be sent wirelessly via our products. Electric utilities worldwide can use wireless solutions for monitoring and controlling vital processes in the development and distribution of electricity including data from substations, capacitor banks and high tension lines. Use wireless to link various segments of their infrastructure, and to monitor and control alarms and sensors. contact US Today!

Visual Remote and Securely we help you Control your Obstruction Lighting, Heliport Lighting, Airfield Lighting

IP Video Anywhere Solar-Powered Wireless Camera Got facilities you need to keep an eye on? Oftentimes they're several miles from your headquarters and, worse, you can't get any electricity (let alone Ethernet) to an exterior location where you'd like to mount a camera. Companies with remote or hard to access assets, such as oil and gas pipelines, bridges or rural properties, have not had an effective, economical solution for protecting those assets. iPhone Remote Control for Video IP Any Where!

XStream Family Flexibility Smaller than a credit card, the XStream Family™ of Wireless OEM Modules is designed around a single form factor that allows interchangeability between 9XStream (900 MHz) and 24XStream (2.4 GHz) modules. This unique feature allows OEMs the flexibility to develop domestic and international products with identical layouts. Simply plug in a 900 MHz module for shipment to domestic markets or a 2.4 GHz module for international markets.

Communications and data transmission antennas. Yagis Omnis Mobiles Rings Broadband Arrays Sigflex Phone & Radio Antennas Mobile Mounts Accessories Ultra Link Cable

Automation Wireless Solution Provider IQ Sensors 418 - IQ Sensors 900 -  Wireless I/O - Software Industrial Ethernet Products Automation - Industrial Ethernet Products - SCADA   Power Supplies - Solar Power SCADA   iPhone Remote Control for Video IP Any Where! IQ Traffic control and access control products Traffic Signal Monitors . signal monitors, vehicle detectors, power supplies, load switches, flashers, bus interface units, and detector harnesses) that offer value added benefits for traffic signal cabinets as well as gate, parking, and/or door operators UPS backup your traffic systems with IQFuelCell IQEnergy: IQ Fuel cells are now available as an alternative source for renewable energy. Unlike traditional power generators, they don't require gasoline to generate power. They also provide an alternative to solar generators because they do not depend on any external power gathering equipment. These units are compact, durable, and built to power a wide range of applications. The Best Generator Ever! Applications: Airports, Computer Rooms, Hospitals, Traffic, UPS Signal Conditioning (ADAM-3000) The ADAM-3000 series modules are the most cost-efficient, field configurable isolation-based signal conditioners on the market today. These modules are easily installed to protect your instruments and process signals from the harmful effects of ground loop, motor noise, and other electrical interference. Remote I/O Module (ADAM-4000) In order to provide the best Remote DA&C system solution to fully fit the request from industrial users, ADAM-4000 series has been improved with two design concepts: Industrial standard and Intelligent functions. Distributed I/O System (ADAM-5000) ADAM-5000 Ethernet I/O system and isolated I/O modules now available are bringing new communication performance and system reliability to the ADAM product line, and to the Industrial Automation industry in general. Smart Web I/O Modules (ADAM-6000) ADAM-6000 Smart Web I/O Module is an industrial-grade Ethernet hub/switch for Ethernet networking solutions in Industrial Automation environments. It allows users to expand their industrial networks fast and cost-effectively. SCADA - Wireless SCADA systems: Industrial Automation, Process Automation, Factory Automation, Machine Control, Motion Control, Process Control & Instrumentation RF Wireless Solutions, RF, Wireless Data Collection, Industrial RF solutions, SCADA, wireless SCADA, RF SCADA monitoring, wireless transceivers Data from and control signals to pipes, valves and pumps can be sent wirelessly via our products. Electric utilities worldwide can use wireless solutions for monitoring and controlling vital processes in the development and distribution of electricity including data from substations, capacitor banks and high tension lines. Use wireless to link various segments of their infrastructure, and to monitor and control alarms and sensors. Contact US Today! The ADOTT global leader, providing a full range of industrial DA&C products. With rich terminal modules and software support, Adott provides high-speed, high quality yet cost saving products for industrial requirements. ADOTT plug-in I/O solutions meet all your requirements in most general purpose Machine Automation applications. Both positioning control and velocity control are supported. Data Acquisition and Remote Monitoring of Energy production and distribution systems: PV Solar Powered, wind and fuel Cells generators. Data Acquisition Service Data acquisition is the process of gathering information in an automated fashion from analog and digital measurement sources such as sensors and devices under test. Data acquisition uses a combination of PC-based measurement hardware and software to provide a flexible, user-defined measurement system. PCI-Bus Half-size PCI-Bus DA&C cards follow the industrial standard form factor of half-length ISA and PCI add-on cards. ISA-Bus Data acquisition and control hardware generally performs one or more of the following functions: analog input, analog output, digital input, digital output and counter/timer functions. PC/104 Embedded applications offen require specific features, creating a custom made board with desired features and characteristics is expensive and time consuming. A simpler and more cost-effective solution is to add features by incorporating PC/104 modules. Motion ADOTT Stepping/Pulse-type Servo Motor Control Card is designed for general-purpose extreme motion applications. For advanced applications, we supply Windows DLL drivers and user-friendly examples to decrease your programming load. MIC-2000 The MIC-2000 series is a family of rugged and flexible PC compatible industrial computers. Based on open ISA-bus passive backplane technology, its flexible modular system design makes upgrades and maintenance simple. With superior mechanical reliability and bus extension capabilities, the MIC systems are ideal for use in applications where a harsh or vibrationprone environment would prohibit the use of a standard office PC or compatible. ADAM-5511 System Specifications PC-based Programmable Standalone Controller Main Features Network Nodes: 32 nodes (ADAM-4000) Network Nodes: 64 Communication Protocol: Modbus/RTU Communication Network: RS-485 Communication Port: RS-485 x 1, RS-232 x 1 Programming Language: C language I/O Points: 64 (4 I/O slots) Communication Speed: up to 115.2 kbps Introduction The ADAM-5511 is a PC-based programmable micro-controller for standalone data acquisition and control system. It¡¦s IBM-PC compatible hardware and operating system runs programs written in both assembly and high-level languages. Each system can handle up to four I/O modules (up to sixty-four I/O points). The system also provides serial communication ports (RS-232/485), allowing the system to communicate with other Modbus devices for versatile applications. Power your electronic projects with OkSolar energy Fuel Cells Backup by IQFuelCell.com Enclosures and Out Door Cabinets Battery Charger: 12Volts, 24 Volts, 36Volts, 48 Volts -120VAC or 230VAC Using state-of-the-art, switch-mode technology, the DLS Power Supply series is engineered with the user and variable environmental conditions in mind. Extra care has been given to insure many years of service-free operation, even when subjected to extremely harsh conditions. Batteries are charged quickly and efficiently without over charging and pumps, motors, and fans operate perfectly for prolonged life. IOTA Engineering uses advanced switch mode technology to bring to market highly sophisticated electronic converter/power supplies at appealing affordability. Exceptionally clean DC output insures pumps, motors, fans, and lights work perfectly. This means longer life for any connected load; virtually no AC ripple to cause static or premature failure of radio or television equipment. Inverter/Charger Available in 12 - 24- and 48-volt models, it provides utility-grade output power and offers high surge capacity 105 VAC/60 Hz - 105 VAC/50 Hz - 120 VAC/60 Hz - 220 VAC/60 Hz - 230 VAC/50 Hz-DC to DC Converters -DC to DC Converters Din Rail -Din Rail Linear Power Supplies -DIN Rail power supplies -Din Rail Single Phase Power Supplies -Din Rail Unregulated Line Power Supplies -Din Rail Voltage Regulator -Inverters Accessories -Inverters DC/AC -Mini Power -Power Supplies -Power Transformers -Transformer IQEnergy: IQ Fuel cells are now available as an alternative source for renewable energy. Unlike traditional power generators, they don't require gasoline to generate power. They also provide an alternative to solar generators because they do not depend on any external power gathering equipment. These units are compact, durable, and built to power a wide range of applications. The Best Generator Ever!  Applications: Airports, Computer Rooms, Hospitals,  Traffic, UPS Smart designs with IQ Fuel Cells for smart energy applications Contact us today! >

WARNING: EXPLOSION HAZARD Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous NOTICE These devices must be wired in accordance with Class I, Division 2 wiring methods as described in the National Electrical Code, Article 501-4(b) or the authority having jurisdiction. Transmitter unit is to be used with a purely resistive antenna when installed in Class I, Division 2 areas.