IQ Sensor 900 MHz. FCC certified radio transmitter

IQXR product family consists of Temperature, Humidity, Thermistor (10K & 100K), Pulse Counter, and Analog Input Modules with integrated 100mw, 900 MHz Spread Spectrum Frequency Hopping transmitters for long range performance.

IQ Sensors 418 - IQ Sensors 900 - Wireless I/O - Software

Industrial Ethernet Products

Automation - Industrial Ethernet Products - SCADA

Power Supplies - Solar Power SCADA

IQ Sensor Temperature/Humidity 900
900 MHz Transmitter
The IQ Sensor Temp/Humidity-900 sensor is a battery operated temperature and humidity sensor with a microprocessor controlled 900 MHz. FCC certified radio transmitter.

IQ Sensor Temperature/Humidity 900
900 MHz Transmitter

Main Features
Sensirion SHT71 single chip temperature/humidity sensor
Calibration/linearization data stored in sensor
Integrated 100mw, 900 MHz SSFH radio for long range performance
Optional 2.4 GHz radio
30-Bit unique ID
Range Indoor: Up to 1300 feet
Range Outdoor: Up to 1 mile with standard antenna
Battery lasts up to 3 years at 5 minute transmit intervals (6 years with optional battery pack)
Very small (3.25” X 3.25” X 1.375”) ABS Enclosure
Complies with part 15 of the FCC rules
CRC-16 error checked Status, ID and Temperature
External ¼ wave antenna with RPSMA connector (Optional antennas available)
Conformal coated

Description:
The IQ Sensor Temp/Humidity-900 sensor is a battery operated temperature and humidity sensor with a microprocessor controlled 900 MHz. FCC certified radio transmitter. The IQ Sensor Temp/Humidity-900 sensor has an on board clock that allows it to spend most of the time in a low power quiescent state.
At predetermined time intervals the clock will wake up the onboard microprocessor. Unique serial number information, linearized temperature, linearized and temperature compensated humidity data are combined with a CRC-16 error check and transmitted in a very short data packet that results in a very short transmitter on-time. This architecture allows the IQ Sensor Temp/Humidity-900 sensor to consume very low energy resulting in a battery life of up to 3 years (6 years with optional battery pack).

The electronics are coated with a conformal material that provides a moisture barrier against condensation. Submersion in water is not recommended.
An internal reed switch permits a user to activate the service switch with a magnet. The Sensor is shipped with the transmitter turned off (anytime the Sensor is to be shipped the transmitter should be turned off or must be placed in a shielded container to prevent interference that might cause shipping problems). The sensor is started by loosening the lid screws and removing the battery pull tab. When a magnet is swiped across the enclosure at the “Service” label, a data transmission occurs immediately and a special mark is introduced in the ID field of the transmitted data packet to indicate which sensor is in service or installation. The IQ Sensor Temp/Humidity-900 sensor can be turned off by removing the batteries or reinstalling a battery pull tab.

Universal Output Module

The Universal Output Module (UOM) provides analog output in both voltage and current forms as well as discrete form-C relay output.

Main Features
Performs counter-in, analog/relay-out and repeater functions simultaneously
Integrated 100mw, 900 MHz SSFH radio for long-range performance
Outputs voltage, current and form-C relay status from remote sensors
Acts as a 900 MHz. pulse counter
Built-in 900 MHz. packet repeater functions
Learns sensor device IDs from unique packet serial numbers
30-Bit unique ID on UOM (counter) packets
CRC-16 error checked on all packet transfers
Range Indoor: Up to 1300 feet
Range Outdoor: Up to 1 mile with standard antenna
12-24VDC power
Very small (3.25” X 2.5” X 1.125”) ABS Enclosure
External ¼ wave antenna or internal wire

Description:
The Universal Output Module (UOM) provides analog output in both voltage and current forms as well as discrete form-C relay output. The UOM also acts as a counter, producing standard IQ Six radio data packets as a single input counter accumulating active state time and number of activations of a switch closure input. Also, the UOM acts as a standard packet repeater for all IQ Six 900 MHz. radio data packets. The UOM is married to IQ Sensors with a simple ID-learn-sequence that stores sensor IDs in EEPROM so that the UOM knows which devices source the analog and discrete outputs. The UOM can be married to a single analog source and a single discrete source device at the same time while also producing counter device packets and repeating 900 MHz. packets from other IQ Six devices. Analog output is produced in both voltage (0-5V or 0-10V) and current (0-20mA. or 0-40mA) at the same time with a common ground.
The high/low analog output range is controlled by internal jumper selection and is shipped in the low range (0-5V, 0-20mA) mode. The relay output is an isolated form-C with 2-Amp contacts. The counter input is self-excited with 5V at 1 mA. referenced to the same ground as the analog outputs and the power input. This common ground architecture allows the UOM to be substituted for current mode sensors in 4-20 mA. remote applications.

The electronics are coated with a conformal material that provides a moisture barrier against condensation. Submersion in water is not recommended. An internal pushbutton switch permits a user to activate the ID-learn-sequence and service mode functions.

IQ Sensor Temp-900
900 MHz Transmitter
The IQ Sensor Temp-900 sensor is a battery operated digital temperature sensor with a microprocessor controlled 900 MHz. FCC certified radio transmitter.
IQ Sensor Temp-900
900 MHz Transmitter

Main Features
DS 18B20 digital temperature sensor
Linear, no calibration necessary
Slow response - resists short term temperature spikes
Integrated 100mw, 900 MHz SSFH radio for long range performance
Optional 2.4 GHz radio
64-Bit unique ID
Range Indoor: Up to 1300 feet
Range Outdoor: Up to 1 mile with standard antenna
Battery lasts up to 5 years at 5 minute transmit intervals
Very small (3.25” X 2.5” X 1.125”) ABS Enclosure
Complies with part 15 of the FCC rules
CRC-16 error checked Status, ID and Temperature
External ¼ wave antenna
Conformal coated

Description:
The IQ Sensor Temp-900 sensor is a battery operated digital temperature sensor with a microprocessor controlled 900 MHz. FCC certified radio transmitter. The IQ Sensor Temp-900 sensor has an on board time of day clock that allows it to spend most of the time in a low power quiescent state. At predetermined time intervals the clock will wake up the onboard microprocessor. Unique serial number information and digital temperature data are read from a Dallas Semiconductor DS18B20 digital temperature sensor. This information is combined with a CRC-16 error check and transmitted in a very short data packet that results in a very short transmitter on-time. This architecture allows the IQ Sensor Temp-900 sensor to consume very low energy resulting in a battery life of up to 5 years.

The electronics are coated with a conformal material that provides a moisture barrier against condensation. Submersion in water is not recommended. An internal reed switch permits a user to activate the service switch with a magnet. The Sensor is shipped with the transmitter turned off (anytime the Sensor is to be shipped the transmitter should be turned off or must be placed in a shielded container to prevent interference that might cause shipping problems). Start the Sensor by momentarily placing the magnet next to the reed switch as indicated on the product label. When you perform this operation, a data transmission occurs immediately and a special mark is introduced in the ID field of the transmitted data packet to indicate which sensor is in service or installation. The reed switch with magnet is also used to put the Sensor in a quiescent mode (no transmissions and very low power consumption). This is the state the Sensor is in when you receive it from the manufacturer. Place the magnet near the reed switch for 5 seconds or more to enter this powered down state.

IQ Sensor Thermistor 900
900 MHz Transmitter
The IQ Sensor Thermistor 900 wireless transmitter is a battery operated 10K ohm thermistor interface with a microprocessor controlled 900 MHz.

IQ Sensor Thermistor 900
900 MHz Transmitter

Main Features
10K ohm thermistor transmitter (100K option)
Transmits thermistor data with unique ID
Integrated 100mw, 900 MHz SSFH radio for long range performance
Optional 2.4 GHz radio
Range Indoor: Up to 1300 feet
Range Outdoor: Up to 1 mile with standard antenna
Battery lasts up to 5 years with 5 minute transmit rate
Very small (3.25” X 2.5” X 1.125”) ABS Enclosure
Complies with part 15 of the FCC rules
CRC-16 error checked Status, ID and thermistor data
Conformal coated
External ¼ wave antenna

Description:
The IQ Sensor Thermistor 900 wireless transmitter is a battery operated 10K ohm thermistor interface with a microprocessor controlled 900 MHz. FCC certified radio transmitter. The IQ Sensor Thermistor 900 has an on board time of day clock that allows it to spend most of the time in a low power quiescent state. At predetermined time intervals the clock will wake up the onboard microprocessor. Unique serial number information is read from a Dallas Semiconductor 1-wire digital device and thermistor data is read from a 12-bit analog-to-digital converter. This information is combined with a CRC-16 error check and transmitted in a very short data packet that results in a very short transmitter on-time. This architecture allows the IQ Sensor Thermistor 900 to consume very little energy and a battery life of up to 5 years.

The IQ Sensor Thermistor 900 electronics are coated with a conformal material that provides a moisture barrier against condensation. Submersion in water is not recommended. An internal reed switch permits a user to activate the service switch with a magnet. The Sensor is shipped with the transmitter turned off (anytime the Sensor is to be shipped the transmitter should be turned off or must be placed in a shielded container to prevent interference that might cause shipping problems). Start the Sensor by momentarily placing the magnet next to the reed switch as indicated on the product label. When you perform this operation, a data transmission occurs immediately and a special mark is introduced in the ID field of the transmitted data packet to indicate which sensor is in service or installation. The reed switch with magnet is also used to put the Sensor in a quiescent mode (no transmissions and very low power consumption). This is the state the Sensor is in when you receive it from the manufacturer. Place the magnet near the reed switch for 5 seconds or more to enter this powered down state.

IQ Sensor Analog Input
900 MHz Transmitter
The IQ Sensor Analog 900 wireless transmitter is a battery operated 12-bit analog-to-digital converter with a microprocessor controlled 900 MHz.

IQ Sensor Analog Input
900 MHz Transmitter

Main Features
Analog input module
3 Available Models: 0-5vdc, 0-10vdc, or 0-20mA
12-bit Analog to Digital Conversion
Transmits analog value with unique ID
Integrated 100mw, 900 MHz SSFH radio for long range performance
Optional 2.4GHz radio
Range Indoor: Up to 1300 feet
Range Outdoor: Up to 1 mile with standard antenna
Battery lasts up to 5 years at 5 minute transmit intervals
Very small (3.25” X 2.5” X 1.125”) ABS Enclosure
Complies with part 15 of the FCC rules
CRC-16 error checked Status, ID and Analog value
External ¼ wave antenna
Conformal coated

Description:
The IQ Sensor Analog 900 wireless transmitter is a battery operated 12-bit analog-to-digital converter with a microprocessor controlled 900 MHz. FCC certified radio transmitter. The IQ Sensor Analog 900 has an on board time of day clock that allows it to spend most of the time in a low power quiescent state. At predetermined time intervals the clock will wake up the onboard microprocessor. Unique serial number information is read from a Dallas Semiconductor 1-wire digital device and analog data is read from a 12-bit analog-to-digital converter. This information is combined with a CRC-16 error check and transmitted in a very short data packet that results in a very short transmitter on time. This architecture allows the IQ Sensor Analog 900 to consume very little energy and a battery life of up to 5 years.

The IQ Sensor Analog 900 electronics are coated with a conformal material that provides a moisture barrier against condensation. Submersion in water is not recommended. An internal reed switch permits a user to activate the service switch with a magnet. The Sensor is shipped with the transmitter turned off (anytime the Sensor is to be shipped the transmitter should be turned off or must be placed in a shielded container to prevent interference that might cause shipping problems). Start the Sensor by momentarily placing the magnet next to the reed switch as indicated on the product label. When you perform this operation, a data transmission occurs immediately and a special mark is introduced in the ID field of the transmitted data packet to indicate which sensor is in service or installation. The reed switch with magnet is also used to put the Sensor in a quiescent mode (no transmissions and very low power consumption). This is the state the Sensor is in when you receive it from the manufacturer. Place the magnet near the reed switch for 5 seconds or more to enter this powered down state.

IQ Sensor Pulse Counter 900
900 MHz Transmitter
The IQ Sensor Pulse Counter 900 wireless transmitter is a battery operated digital counter with a microprocessor controlled 900 MHz. FCC certified radio transmitter.
IQ Sensor Pulse Counter 900
900 MHz Transmitter

Main Features
24-bit Digital Counter with 30-bit unique ID
Counts up to 60,000 pulses per minute
Integrated 100mw, 900 MHz SSFH radio for long range performance
Optional 2.4 GHz radio
Range Indoor: Up to 1300 feet
Range Outdoor: Up to 1 mile with standard antenna
Battery lasts up to 5 years at 5 minute transmit intervals
Very small (3.25” X 2.5” X 1.125”) ABS Enclosure
Complies with part 15 of the FCC rules
CRC-16 error checked Status, Counts, ID and Temperature
External ¼ wave antenna
Conformal coated

Description:
The IQ Sensor Pulse Counter 900 wireless transmitter is a battery operated digital counter with a microprocessor controlled 900 MHz. FCC certified radio transmitter. The IQ Sensor Pulse Counter 900 has an on board time of day clock that allows it to spend most of the time in a low power quiescent state.
At predetermined time intervals the clock will wake up the onboard microprocessor. Unique serial number information is read from a Dallas Semiconductor 1-wire digital device and counter data is read from a 24-bit internal counter register. This information is combined with a CRC-16 error check and transmitted in a very short data packet that results in a very short transmitter on-time. This architecture allows the IQ Sensor Pulse Counter 900 to consume very little energy and a battery life of up to 5 years.

The IQ Sensor Pulse Counter 900 electronics are coated with a conformal material that provides a moisture barrier against condensation. Submersion in water is not recommended. An internal reed switch permits a user to activate the service switch with a magnet. The Sensor is shipped with the transmitter turned off (anytime the Sensor is to be shipped the transmitter should be turned off or must be placed in a shielded container to prevent interference that might cause shipping problems). Start the Sensor by momentarily placing the magnet next to the reed switch as indicated on the product label. When you perform this operation, a data transmission occurs immediately and a special mark is introduced in the ID field of the transmitted data packet to indicate which sensor is in service or installation. The reed switch with magnet is also used to put the Sensor in a quiescent mode (no transmissions and very low power consumption). This is the state the Sensor is in when you receive it from the manufacturer. Place the magnet near the reed switch for 5 seconds or more to enter this powered down state.

IQ Sensors 418 - IQ Sensors 900- Wireless I/O - Software