48403 Sensor Motion Wireless - Solutions Provider! Wireless Sensors Wireless Receivers Wireless Transmitters.

Wireless Sensors, Sensor Motion, Wireless Receivers, Wireless Transmitters, Wireless Antennas

High value wireless solutions for the automation and communications industry

Sensor Motion 418 MHz Transmitter

Main Features
Digital motion measurement via internal weighted accelerometer
64-Bit unique ID
Up to 600 foot transmission range
30 second transmission interval
Patent pending
Battery life up to 5 years
Very small (1.3” X 2.1” X .6”) ABS enclosure
Complies with part 15 of the FCC rules
Water resistant coating for wet environments
Internal loop antenna
Low cost

Description:
The Point Sensor Motion sensor is a battery operated digital motion sensor with a microprocessor controlled 418 MHz. FCC certified radio transmitter. The Point Sensor Motion sensor has an on board time of day clock that allows it to spend most of the time in a low power quiescent state. At predetermined time intervals the clock will wake up the onboard microprocessor. Unique serial number information and digital motion data is combined with a CRC-16 error check and transmitted in a very short data packet that results in a transmitter on time of only 15 milliseconds. This architecture allows the Point Sensor Motion sensor to consume very low energy resulting in a battery life of up to 5 years.

The electronics are coated with a conformal rubber material that provides a moisture barrier against condensation. Submersion in water is not recommended.
An integral pushbutton is used to activate the service switch. The Sensor is shipped with the transmitter turned off (anytime the Sensor is to be shipped the transmitter should be turned off or must be placed in a shielded container to prevent interference that might cause shipping problems). Start the Sensor by momentarily pushing the service switch (you will feel the button click). When the service switch is pushed a data transmission occurs immediately and a special mark is introduced in the ID field of the transmitted data packet to indicate which sensor is in service or installation. The service switch is also used to put the Sensor in a quiescent mode (no transmissions and very low power consumption). This is the state the Sensor is in when you receive it from the manufacturer. Push and hold the service switch for 5 seconds or more to enter this powered down state.

Technical Features:

Transmission rate	30 seconds
Shelf life with battery installed	10 Years in quiescent mode
Dimensions (enclosure)	1.5 W X 2.1 H X .6 D (inches)
Weight	1.0 oz.
Storage Temperature	-40° to 85° C
Operating Temperature	-40° to 85° C
Battery life with transmissions	3-7 years
Battery	3.6 volt Lithium

Wireless Receivers: A complete family of wireless RF sensors, transmitters, loggers, repeaters, receivers and servers spanning the 418MHz. to 2.4GHz frequency range. With an emphasis on modularity and compatibility, The Point Family is ideally suited for a broad range of applications from basic telemetry to custom engineered wireless networking solutions.

Wireless Sensors: Adott offers an expanded line of wireless sensors to measure temperature, relative humidity, pressure, vibration, analog voltage and current, and discrete digital inputs. Each sensor is battery operated and fitted with a microprocessor controlled 418 MHz radio transmitter.

Automation Wireless Solution Provider

IQ Sensors 418 - IQ Sensors 900 - Wireless I/O - Software

Industrial Ethernet Products

Automation - Industrial Ethernet Products - SCADA

Power Supplies - Solar Power SCADA

BBS Battery backup system (BBs) that provide battery power to traffic intersections.

iPhone Remote Control for ip Video any Where!

iPhone Remote Control for Video IP Any Where!

IQ Traffic control and access control products Traffic Signal Monitors .
signal monitors, vehicle detectors, power supplies, load switches, flashers, bus interface units, and detector harnesses) that offer value added benefits for traffic signal cabinets as well as gate, parking, and/or door operators

UPS backup your traffic systems with IQFuelCell

IQEnergy: IQ Fuel cells are now available as an alternative source for renewable energy. Unlike traditional power generators, they don't require gasoline to generate power. They also provide an alternative to solar generators because they do not depend on any external power gathering equipment. These units are compact, durable, and built to power a wide range of applications.
The Best Generator Ever!
Applications: Airports, Computer Rooms, Hospitals, Traffic, UPS

computer, automation, industrial, embedded, control, application, PC, PC-based, PC-based automation, research, R&D, ODM, OEM, sales, consulting, electronics, analog, digital, support, technical support, manufacturing, manufacturer, hardware, global, IPC, IC, CTI, CT, EPC, PPC, IA, HMI, MMI, CPU, solutions, SBC, SBCs, single board computer, single board computers, CPU card, Biscuit, POS, compact PCI, CompactPCI, computer telephony, PC/104, chassis, peripherals, SSD, industrial workstations, industrial PC, industrial communication, signal conditioning, distributed, remote, data acquisition, DA&C, industrial controller, RAID, automation software, life automation, control

Signal Conditioning (ADAM-3000)
The ADAM-3000 series modules are the most cost-efficient, field configurable isolation-based signal conditioners on the market today. These modules are easily installed to protect your instruments and process signals from the harmful effects of ground loop, motor noise, and other electrical interference.

Remote I/O Module (ADAM-4000)
In order to provide the best Remote DA&C system solution to fully fit the request from industrial users, ADAM-4000 series has been improved with two design concepts: Industrial standard and Intelligent functions.

Distributed I/O System (ADAM-5000)
ADAM-5000 Ethernet I/O system and isolated I/O modules now available are bringing new communication performance and system reliability to the ADAM product line, and to the Industrial Automation industry in general.

Smart Web I/O Modules (ADAM-6000)
ADAM-6000 Smart Web I/O Module is an industrial-grade Ethernet hub/switch for Ethernet networking solutions in Industrial Automation environments. It allows users to expand their industrial networks fast and cost-effectively.

SCADA - Wireless SCADA systems:
Industrial Automation, Process Automation, Factory Automation, Machine Control, Motion Control, Process Control & Instrumentation

RF Wireless Solutions, RF, Wireless Data Collection, Industrial RF solutions, SCADA, wireless SCADA, RF SCADA monitoring, wireless transceivers
Data from and control signals to pipes, valves and pumps can be sent wirelessly via our products.

Electric utilities worldwide can use wireless solutions for monitoring and controlling vital processes in the development and distribution of electricity including data from substations, capacitor banks and high tension lines.

Use wireless to link various segments of their infrastructure, and to monitor and control alarms and sensors.

The ADOTT global leader, providing a full range of industrial DA&C products. With rich terminal modules and software support, Adott provides high-speed, high quality yet cost saving products for industrial requirements. ADOTT plug-in I/O solutions meet all your requirements in most general purpose Machine Automation applications. Both positioning control and velocity control are supported.

Data Acquisition and Remote Monitoring of Energy production and distribution systems: PV Solar Powered, wind and fuel Cells generators. Data Acquisition Service
Data acquisition is the process of gathering information in an automated fashion from analog and digital measurement sources such as sensors and devices under test. Data acquisition uses a combination of PC-based measurement hardware and software to provide a flexible, user-defined measurement system.

PCI-Bus
Half-size PCI-Bus DA&C cards follow the industrial standard form factor of half-length ISA and PCI add-on cards.

ISA-Bus
Data acquisition and control hardware generally performs one or more of the following functions: analog input, analog output, digital input, digital output and counter/timer functions.

PC/104
Embedded applications offen require specific features, creating a custom made board with desired features and characteristics is expensive and time consuming. A simpler and more cost-effective solution is to add features by incorporating PC/104 modules.

Motion
ADOTT Stepping/Pulse-type Servo Motor Control Card is designed for general-purpose extreme motion applications. For advanced applications, we supply Windows DLL drivers and user-friendly examples to decrease your programming load.

MIC-2000
The MIC-2000 series is a family of rugged and flexible PC compatible industrial computers. Based on open ISA-bus passive backplane technology, its flexible modular system design makes upgrades and maintenance simple. With superior mechanical reliability and bus extension capabilities, the MIC systems are ideal for use in applications where a harsh or vibrationprone environment would prohibit the use of a standard office PC or compatible.

ADAM-5511

System Specifications PC-based Programmable Standalone Controller

Main Features

Network Nodes: 32 nodes (ADAM-4000)

Network Nodes: 64

Communication Protocol: Modbus/RTU

Communication Network: RS-485

Communication Port: RS-485 x 1, RS-232 x 1

Programming Language: C language

I/O Points: 64 (4 I/O slots)

Communication Speed: up to 115.2 kbps

Introduction

The ADAM-5511 is a PC-based programmable micro-controller for standalone data acquisition and control system. It¡¦s IBM-PC compatible hardware and operating system runs programs written in both assembly and high-level languages. Each system can handle up to four I/O modules (up to sixty-four I/O points). The system also provides serial communication ports (RS-232/485), allowing the system to communicate with other Modbus devices for versatile applications.

Battery Charger:

12Volts, 24 Volts, 36Volts, 48 Volts -120VAC or 230VAC Using state-of-the-art, switch-mode technology, the DLS Power Supply series is engineered with the user and variable environmental conditions in mind. Extra care has been given to insure many years of service-free operation, even when subjected to extremely harsh conditions. Batteries are charged quickly and efficiently without over charging and pumps, motors, and fans operate perfectly for prolonged life.
IOTA Engineering uses advanced switch mode technology to bring to market highly sophisticated electronic converter/power supplies at appealing affordability.

Exceptionally clean DC output insures pumps, motors, fans, and lights work perfectly. This means longer life for any connected load; virtually no AC ripple to cause static or premature failure of radio or television equipment.

Inverter/Charger Available in 12 - 24- and 48-volt models, it provides utility-grade output power and offers high surge capacity
105 VAC/60 Hz - 105 VAC/50 Hz - 120 VAC/60 Hz - 220 VAC/60 Hz - 230 VAC/50 Hz-DC to DC Converters
-DC to DC Converters Din Rail
-Din Rail Linear Power Supplies
-DIN Rail power supplies
-Din Rail Single Phase Power Supplies
-Din Rail Unregulated Line Power Supplies
-Din Rail Voltage Regulator
-Inverters Accessories
-Inverters DC/AC
-Mini Power
-Power Supplies
-Power Transformers
-Transformer

IQEnergy: IQ Fuel cells are now available as an alternative source for renewable energy. Unlike traditional power generators, they don't require gasoline to generate power. They also provide an alternative to solar generators because they do not depend on any external power gathering equipment. These units are compact, durable, and built to power a wide range of applications.

The Best Generator Ever!
Applications: Airports, Computer Rooms, Hospitals, Traffic, UPS

Smart designs with IQ Fuel Cells for smart energy applications Contact us today! >

GeneralCommunications Wireless Solutions Provider putting the latest RF and IR technology to work to enhance productivity and increase profits. More than a radio company, GeneralCommunications Point Wireless combines wireless (RF & IR) data transmission with extensive array of sensors and application specific modules suited for a variety of common applications. GeneralCommunications works closely with OEMs in dozens of industries to capitalize on the benefits of wireless technology. All products are general purpose in design and appeal to a broad customer base. Typical deployments include traffic light automation, food safety, energy management, access control, fire safety and trucking. The GeneralCommunications value proposition is based on the ability to engineer application specific solutions ranging from basic telemetry to wireless networking. This value arises from GeneralCommunications application awareness and the command of innovative, high value designs. In addition to application specific solutions, Point Six Wireless also offers a complete line of general purpose products for the transmission of Ethernet, serial, Modbus, Weigand, analog, discrete or sensor based data.

Wireless Solution Provider

Sensor with integrated Transmitters Adott offers an expanded line of wireless sensors to measure temperature, relative humidity, pressure, vibration, analog voltage and current, and discrete digital inputs. Each sensor is battery operated and fitted with a microprocessor controlled 418 MHz radio transmitter.
Item#	Description
48400	Sensor Temperature Wireless Temperature and Unique ID Transmitter. Main Features: Digital temperature measurement 64-Bit Unique ID Up to 600 foot transmission range Transmission intervals from 10 to 240 seconds Battery life up to 5 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Complies with part 15 of the FCC rules Water resistant coating for wet environments Internal Loop antenna Low Cost.
	Sensor Counter/Temperature 418 MHz Digital Counter and Temperature Sensor The Point Sensor Counter/Temperature wireless transmitter is a battery operated digital counter and temperature sensor with a microprocessor controlled 418 MHz. Main Features 32-Bit unique ID with 24-bit Digital Counter, 13-bit Temperature, digital input status Switch for installation and service mode indication Broad operating temperature range Up to 600-foot range Transmission rates from 10 to 240 seconds Up to 100 transmitters can coexist Battery lasts from 5 to 10 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Complies with part 15 of the FCC rules Water resistant coating on PCB CRC-16 checked Status, ID, temperature and counter data Internal Loop antenna
48415	Sensor Analog 5V 418 MHz transmitters with analog input and Unique ID Main Features: Analog input 12-bit Analog to Digital Conversion Transmits Unique ID and analog value Up to 600-foot transmission range Transmission intervals from 10 to 240 seconds Patent Pending Modulator Battery life up to 5 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Complies with part 15 of the FCC rules Water resistant coating on PCB Internal Loop antenna Low Cost
48416	Sensor Analog 10V 418 MHz transmitters with 12-bit analog input/ Unique ID Main Features: Analog input 12-bit Analog to Digital Conversion Transmits Unique ID and analog value Up to 600 foot transmission range Transmission intervals from 10 to 240 seconds Patent Pending Modulator Battery life up to 5 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Complies with part 15 of the FCC rules Water resistant coating on PCB Internal Loop antenna Low Cost
48417	Sensor Analog 20mA 418 MHz transmitters with analog input / Unique ID Main Features: Analog input 12-bit Analog to Digital Conversion Transmits Unique ID and analog value Up to 600 foot transmission range Transmission intervals from 10 to 240 seconds Patent Pending Modulator Battery life up to 5 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Complies with part 15 of the FCC rules Water resistant coating on PCB Internal Loop antenna Low Cost
48413	Sensor Temperature / Humidity Wireless Temperature and Relative Humidity Transmitter Main Features: Measures Temperature and Relative Humidity Up to 600-foot transmission range Transmission rates from 10 to 240 seconds Patent Pending Modulator Battery life up to 5 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Broad operating temperature range Complies with part 15 of the FCC rules Water resistant coating on PCB Internal Loop antenna Low Cost
48409	Sensor Magnetic Door Open/close 418 MHz Transmitter Main Features 32-Bit unique ID with 24-bit Digital Counter, digital input status Switch for installation and service mode indication Up to 600-foot range Transmits immediately on status change Up to 100 transmitters can coexist Battery lasts from 5 to 10 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Complies with part 15 of the FCC rules Water resistant coating on PCB CRC-16 checked Status, ID and counter data Internal Loop antenna Low Cost
	Light
48403	Sensor Motion 418 MHz Transmitter Main Features Digital motion measurement via internal weighted accelerometer 64-Bit unique ID Up to 600 foot transmission range 30 second transmission interval Patent pending Battery life up to 5 years Very small (1.3” X 2.1” X .6”) ABS enclosure Complies with part 15 of the FCC rules Water resistant coating for wet environments Internal loop antenna Low cost
48418	Sensor Pressure 418 MHz Pressure Transmitter Main Features Digital pressure measurement 64-Bit Unique ID Up to 600 foot transmission range Transmission intervals from 10 to 240 seconds Patent Pending Modulator Battery life up to 10 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Complies with part 15 of the FCC rules Water resistant coating for wet environments Internal Loop antenna Low Cost
48404	Sensor Power Monitor 418 MHz Transmitter Main Features Measures current draw 64-Bit unique ID 12-bit analog to digital conversion Transmits unique ID and analog value Up to 600 foot transmission range Transmission intervals from 10 to 240 seconds Patent pending modulator Battery life up to 5 years Very small (1.3” X 2.1” X .6”) ABS enclosure Water resistant coating on PCB Internal loop antenna Low cost
Discrete input
48401	Sensor Pulse Counter 418 MHz Transmitter Main Features 30-Bit unique ID with 24-bit Digital Counter and radio transmitter Counts up to 60,000 pulses per minute Switch for installation and service mode indication Broad operating temperature range Up to 600-foot range Transmission rates from 10 to 240 seconds Up to 100 transmitters can coexist Battery lasts from 6 to 10 years Very small (1.3” X 2.1” X .6”) ABS Enclosure Complies with part 15 of the FCC rules Water resistant coating on PCB CRC-16 checked Status, ID, and counter data Internal Loop antenna Low Cost
48410	Sensor RF Identification 418 MHz. FCC Certified Radio Transmitter Main Features 64-Bit unique ID Up to 600 foot transmission range Transmission intervals from 10 to 240 seconds Patent pending Battery life up to 5 years Very small (1.4” X 2.1” X .6”) ABS enclosure Complies with part 15 of the FCC rules Water resistant coating for wet environments Internal loop antenna Low cost
48405	Sensor Vibration 418 MHz Transmitter Main Features Digital broad range vibration measurement via internal accelerometer 64-Bit unique ID Up to 600 foot transmission range 30 second transmission interval Patent pending Battery life up to 5 years Very small (1.3” X 2.1” X .6”) ABS enclosure Complies with part 15 of the FCC rules Water resistant coating for wet environments Internal loop antenna Low cost
	Fire Extinguisher
48402	Sensor Thermistor 418 MHz Transmitter The Point Sensor Thermistor wireless transmitter is a battery operated 10K thermistor interface with a microprocessor controlled 418 MHz.
IR Traffic Counters
48407	Counter IR Beam Traffic Counter Battery powered - up to 2 year operation Local display Integrated 418MHz/433MHz transmitter High Impact ABS Enclosure (1.3" x 2.1" x .6")
48408	Counter Plus IR Beam Traffic Counter Battery powered - up to 2 year operation Local display Integrated 418MHz/433MHz transmitter High Impact ABS Enclosure (1.3" x 2.1" x .6")
48412	Counter LV IR Beam Traffic Counter - reflective Low voltage powered Local display Integrated 418MHz/433MHz transmitter High Impact ABS Sensor Enclosure (1.3" x 2.1" x .6")
48414	Counter MOD IR Beam Traffic Counter - reflective Low voltage powered Local Display Optional Dual Beam Optional plug-in transmitter (418/433/900MHz/2.4Ghz) Accommodates external sensors High Impact ABS Sensor Enclosure (3.3" x 3.3" x 1.25")
48419	Proximity Counter IR Beam Proximity Counter No reflector required Range up to 7 feet/2.3 meters Battery powered - up to 2 year operation Integrated 418MHz/433MHz transmitter High Impact ABS Enclosure (1.3" x 2.1" x .6")

Repeat and Log Data

GC Repeater

Repeater
418 MHz RF Receiver with 900 MHz or 2.4 GHz RF Transceiver

Main Features
418 MHz Receiver range up to 600 feet.
Built in 900 MHz. or 2.4 GHz. frequency hopping radio for long-range wireless interface.
Transceiver Range Indoor: 600’ to 1300’ (900 MHz); 300’ to 750’ (2.4 GHz).
Transceiver Range Outdoor (with dipole): 7mi. (900 MHz); 3mi. (2.4 GHz).
Transceiver Range Outdoor (with high gain antenna): >20mi. (900 MHz); >12mi. (2.4 GHz).
Supports all Point Sensors and LSX transmitters
Low power, 6-24 VDC at 200 milliamp transmitting, 70 milliamp receiving.

GC Integrator Logger

48420

GC Integrator Logger

RS232
RS422

Integrator Logger
418 MHz. Radio Receiver/Logger and 1-Wire Interface

Main Features
Radio decoder for Point Six wireless sensors
ASCII command support for all 1-Wire™ devices
Decodes CRC-16 error encoded radio packets
Integrated data logger for up to 20 sensors
Programmable serial number filters for 20 sensors
Battery backed Real Time Clock
Provides Search, Family Search and Conditional Search
Block mode commands support all 1-Wire™ device functions
Supports Touch Memory File Structure for Dallas Semiconductor iButtons™
Automatic CRC16 for TMEX™ files
Automatically provides smart strong-pull-up for 1-wire sensors
ESD and over-current Protection on the 1-Wire™ bus
ESD and over-current Protection on the RS485 bus
RS485 Serial Command Interface, (field selectable)
RS232 Serial Command Interface, (field selectable)
Optional 900 MHz. or 2.4 GHz. Radio Network Interface, (field installation)
Optional 418 MHz. radio receiver for Point Sensors, (field installation)
Optional Opto-isolated RS485 Serial Command Interface, (field installation)
Optional Ethernet (TCP/IP) Network Interface, (field installation)
Readable model#, version# and unique 32-bit serial number
Internal antennas for 418 MHz. and 900 MHz. or 2.4 GHz. radios
Dimensions 130 x 130 x 75 MM
Enclosure range-of material: - 40 °C - + 120 °C
Enclosure Temp. range in cont. use: 80 °C

	Access Control
	Portable Card Reader Wireless Portable Proximity/IR Card Reader The Portable Card Reader (PCR) from Point Six Wireless is designed to provide the user with a lightweight, compact and aesthetically pleasing method of reading proximity cards.
	Wireless Stationary Card Reader Wireless Stationary Proximity/IR Card Reader The Stationary Card Reader (SCR) is designed to be used either mounted to a wall or directly to a door and can be operated from external power or internal batteries.
	Access Panel Connectivity Products Access Panel Connectivity The Control Panel Transceiver (CPT) is a compact data transceiver perfect for those needing high performance and dependable operation. The Door Interface Module (DIM) plugs directly into the Access Control Panel and produces a Wiegand output identical to that of a wired system.

Receivers and Web Servers

GCS Server	Input: RS485 Mod Burs Output: RS232 900MHz Ethernet Modem/Cel OPC, DDE drivers Archive Data Control Alarm/Event Utilities	Server Rf Receiver with an Integrated Data Server Main Features 900 MHz or 2.4 GHz Receiver Supports Point Sensors, LSX transmitters via Point Repeater Communicates: Ethernet (TCP/IP), Modem, serial port Data Logger – logs periodic snapshots of the current readings & logs events Web Server – Dynamic HTML web page server showing current readings and alarms Event based alarms – callout or email Push connection to other hosts using TCP/IP based on alarms Simple ASCII command/response protocol 100 Sensors (total of 100 I/O points) maximum 8600 Historical Records capacity 1800 Event Logging capacity Two level password security Each I/O configurable to trigger events Periodic callouts with interval times of 1 minute to 7 days
GCT Transmitter 504452	Output: RS232 RS485 ModBus OPC, DDE, Drives	Transceivers General Purpose 900 MHz./2.4GHz. Spread Spectrum Frequency Hopping Transceivers Main Features LED power and configuration activity indicator Astron AXH900RP SMA R Reverse Polarity SMA 6.5” Antenna High Impact ABS enclosure Channel Capacity hops through 25 channels, Up to 65,000 NetIDs Serial Data Interface Asynchronous (RS-232) CMOS (TTL) signals, 5V, 3.3V tolerant I/O Data Rate - 9600 or 19200 bps Transport Protocol - Transparent networking Network Topology - Multi-drop Channel Data Rate - 10k or 20k bps respectively (vary with data rate) Transmit Power Output - 100mW Rx Sensitivity: -110 or -107 respectively Range - Indoor: 600’ to 1300’ Outdoor: 7mi. with dipole, >20mi. with high gain antenna Interference Rejection - 70 dB at pager and cellular phone frequencies
504454		GCTZR-MA 900-MHz frequency-hopping RS485 Master/Slave auto-sensing radio interface The TZR-MA uses an embedded 100-milliwatt frequency hopping wireless modem that provides communication between a local RS485 network and a remote network of RS485 connected devices.
GCV View	Output: RS232 RS485 OPC, DDE, Drives	View RF Receiver Main Features High performance 418 MHz receiver Compatible with OneSix DDE Server and OPCServer PointView PC Software included Serial connection directly to a PC Powered by RS232 port or external source ASCII radio packet data output Decodes CRC-16 error encoded radio packets DB-9 connector for RS232 interface Up to 480 ft. range
GCH Host	Output: RS232 RS485 OPC, DDE, Drives	Host Low Cost RS232 or RS422 ASCII output 418 MHz. Receiver Main Features: High performance 418 MHz receiver Serial connection directly to a PC Powered by RS232 port or external source. ASCII radio packet data output. Decodes CRC-16 error encoded radio packets. DB-9 connector for RS232/RS422 interface. 600 ft. maximum range

Receivers

View Receiver

418MHz/433MHz receiver
RS 232 output
ASCI format data
450 feet range

Host Receiver

418MHz/433MHz receiver
RS 232 output
ASCI format data
600 feet range

Mesh Repeater

418MHz/433MHz to 900MHz/2.4GHz repeating
900MHz to 900MHz SS FH mesh network repeating
Serial outputs
Self configuring
2000 feet indoor range per Repeater

Manager

900MHz/2.4GHz SS FH transceiver
TCP/IP output
Optional browser based traffic reports
OPC/DDE drivers
XML compliant
Data archiving
2000 feet indoor range

Server

900MHz/2.4GHz SS FH transceiver
TCP/IP output
Modem output
Optional browser based traffic reports
OPC/DDE drivers
XML compliant
Data archiving
2000 feet indoor range

Note: To view the above PDF documents, you will need the free Adobe Acrobat Reader

Wireless Sensors, Wireless Receivers, Wireless Sensors, Wireless Receivers, high value wireless solutions for the automation and communications industry!