|
|
Wireless Sensors, Sensor Counter/Temperature, Wireless Receivers, Wireless
Transmitters, Wireless Antennas
High value wireless solutions for the automation and communications industry
Point Sensor Counter/Temperature
418 MHz Digital Counter and Temperature Sensor
Main Features
32-Bit unique ID with 24-bit Digital Counter, 13-bit Temperature,
digital input status
Switch for installation and service mode indication
Broad operating temperature range
Up to 600-foot range
Transmission rates from 10 to 240 seconds
Up to 100 transmitters can coexist
Battery lasts from 5 to 10 years
Very small (1.3” X 2.1” X .6”) ABS Enclosure
Complies with part 15 of the FCC rules
Water resistant coating on PCB
CRC-16 checked Status, ID, temperature and counter data
Internal Loop antenna
Low Cost
Description:
The Point Sensor Counter/Temperature wireless transmitter is a
battery operated digital counter and temperature sensor
 with
a microprocessor controlled 418 MHz. FCC certified radio
transmitter. The Point Sensor Counter/Temperature has an on board
time of day clock that allows it to spend most of the time in a low
power quiescent state. At predetermined time intervals the clock
will wake up the onboard microprocessor. Unique serial number
information is read from a Dallas Semiconductor 1-wire digital
device, counter data is read from a 24-bit internal counter
register. This information is combined with a CRC-16 error check and
transmitted in a very short data packet that results in a
transmitter on time of only 15 milliseconds. This architecture
allows the Point Sensor Counter/Temperature to consume very little
energy and a battery life of 5 to 10 year results.
The Point Sensor Counter/Temperature electronics are coated with a
conformal material that provides a moisture barrier against
condensation. Submersion in water is not recommended. A pushbutton
switch in the ABS cover allows the user to activate the service
mode. The service switch has three functions: 1) The Point Sensor
Counter/Temperature is shipped with the transmitter turned off,
anytime the Point Sensor Counter/Temperature is to be shipped the
transmitter should be turned off or placed in a shielded container
to prevent interference. Start the Point Sensor Counter/Temperature
by a momentarily push of the service switch (you will feel the
button click) the Point Sensor Counter/Temperature is started. 2)The
service switch is used as an aid to installation, when the service
switch is pushed a data transmission occurs immediately and a
special mark is introduced in the ID field of the transmitted data
packet to indicate which sensor is in service or installation. 3)The
service switch is used to put the Point Sensor Counter/Temperature
in a quiescent mode (no transmissions and very low power
consumption),this is the state the Point Sensor Counter/Temperature
is in when you receive it from the manufacturer. Push and hold the
service switch for 5 seconds or more to enter this powered down
state. |
Technical Features:
|
Transmission rate |
10-240 seconds (specify when ordering) |
|
Shelf life with battery installed |
5 Years in quiescent mode (10 years with
optional battery) |
|
Dimensions (enclosure) |
1.5 W X 2.1 H X .6 D (inches) |
|
Weight |
1.5 oz. |
|
Operating Temperature |
-40° to 85° C |
|
Input |
Switch closure 3.3 volts pulsed |
|
Humidity |
0% to 90% non-condensing |
|
Battery life with transmissions
|
5-10 years with tx period of 30-240 seconds |
|
Battery |
3.6 volt Lithium |
|
FCC Certified |
FCC ID: M5ZWOWANA |
|
|
|
Wireless Receivers: A complete family of wireless RF sensors, transmitters,
loggers, repeaters, receivers and servers spanning the 418MHz. to 2.4GHz
frequency range. With an emphasis on modularity and compatibility, The Point
Family is ideally suited for a broad range of applications from basic telemetry
to custom engineered wireless networking solutions.
Wireless Sensors: Adott offers an expanded line of wireless sensors to
measure temperature, relative humidity, pressure, vibration, analog voltage and
current, and discrete digital inputs. Each sensor is battery operated and fitted
with a microprocessor controlled 418 MHz radio transmitter.
|
Automation Wireless Solution Provider
|
|
IQ Sensors
418 -
IQ Sensors 900 -
Wireless I/O -
Software
Industrial Ethernet
Products
|
|
Automation -
Industrial Ethernet
Products - SCADA
|
|
Power Supplies -
Solar Power SCADA |
 |
BBS Battery backup system (BBs) that provide battery power
to traffic intersections.
|
 iPhone
Remote Control for Video IP Any Where! |
IQ Traffic control and access control
products
Traffic Signal Monitors .
signal monitors, vehicle detectors, power
supplies, load switches, flashers, bus interface
units, and detector harnesses) that offer value
added benefits for traffic signal cabinets as
well as gate, parking, and/or door operators
|
UPS
backup your traffic systems with IQFuelCell
 IQEnergy:
IQ Fuel cells are now available as an
alternative source for renewable energy.
Unlike traditional power generators,
they don't require gasoline to generate
power. They also provide an alternative
to solar generators because they do not
depend on any external power gathering
equipment. These units are compact,
durable, and built to power a wide range
of applications.
The Best Generator Ever!
Applications: Airports, Computer Rooms,
Hospitals, Traffic, UPS |
|
Signal Conditioning
(ADAM-3000)
The ADAM-3000 series modules are the most
cost-efficient, field configurable isolation-based signal conditioners
on the market today. These modules are easily installed to protect
your instruments and process signals from the harmful effects of
ground loop, motor noise, and other electrical interference. |
 |
Remote I/O Module
(ADAM-4000)
In order to provide the best Remote DA&C system
solution to fully fit the request from industrial users, ADAM-4000
series has been improved with two design concepts: Industrial standard
and Intelligent functions. |
 |
Distributed I/O System
(ADAM-5000)
ADAM-5000 Ethernet I/O system and isolated I/O
modules now available are bringing new communication performance and
system reliability to the ADAM product line, and to the Industrial
Automation industry in general. |
 |
Smart Web I/O Modules
(ADAM-6000)
ADAM-6000 Smart Web I/O Module is an
industrial-grade Ethernet hub/switch for Ethernet networking solutions
in Industrial Automation environments. It allows users to expand their
industrial networks fast and cost-effectively. |
|
SCADA -
Wireless SCADA systems:
Industrial Automation, Process Automation, Factory Automation,
Machine Control, Motion Control, Process Control & Instrumentation
RF Wireless Solutions, RF, Wireless Data Collection, Industrial RF
solutions, SCADA, wireless SCADA, RF SCADA monitoring, wireless
transceivers
Data from and control signals to pipes, valves and pumps can be sent
wirelessly via our products.
Electric utilities worldwide can use wireless solutions for
monitoring and controlling vital processes in the development and
distribution of electricity including data from substations,
capacitor banks and high tension lines.
Use wireless to link various segments of their infrastructure, and
to monitor and control alarms and sensors.
Contact US Today! |
|
The ADOTT global
leader, providing a full range of industrial DA&C products. With
rich terminal modules and software support, Adott provides
high-speed, high quality yet cost saving products for industrial
requirements. ADOTT plug-in I/O solutions meet all your
requirements in most general purpose Machine Automation
applications. Both positioning control and velocity control are
supported.
|
|
|
 |
PCI-Bus
Half-size PCI-Bus DA&C cards follow the
industrial standard form factor of half-length ISA and PCI add-on
cards. |
 |
ISA-Bus
Data acquisition and control hardware generally
performs one or more of the following functions: analog input,
analog output, digital input, digital output and counter/timer
functions. |
 |
PC/104
Embedded applications offen require specific
features, creating a custom made board with desired features and
characteristics is expensive and time consuming. A simpler and
more cost-effective solution is to add features by incorporating
PC/104 modules. |
 |
Motion
ADOTT Stepping/Pulse-type Servo Motor Control
Card is designed for general-purpose extreme motion applications.
For advanced applications, we supply Windows DLL drivers and
user-friendly examples to decrease your programming load. |
 |
MIC-2000
The MIC-2000 series is a family of rugged and
flexible PC compatible industrial computers. Based on open ISA-bus
passive backplane technology, its flexible modular system design
makes upgrades and maintenance simple. With superior mechanical
reliability and bus extension capabilities, the MIC systems are
ideal for use in applications where a harsh or vibrationprone
environment would prohibit the use of a standard office PC or
compatible. |
ADAM-5511
System Specifications PC-based Programmable Standalone
Con troller
Main Features
Network Nodes:
32 nodes (ADAM-4000)
Network Nodes:
64
Communication
Protocol: Modbus/RTU
Communication
Network: RS-485
Communication
Port: RS-485 x 1, RS-232 x 1
Programming
Language: C language
I/O Points: 64
(4 I/O slots)
Communication
Speed: up to 115.2 kbps
Introduction
The ADAM-5511 is a PC-based programmable
micro-controller for standalone data acquisition and control system. It¡¦s
IBM-PC compatible hardware and operating system runs programs written in
both assembly and high-level languages. Each system can handle up to four
I/O modules (up to sixty-four I/O points). The system also provides serial
communication ports (RS-232/485), allowing the system to communicate with
other Modbus devices for versatile applications. |
|
 |
Battery Charger: 12Volts,
24 Volts, 36Volts, 48 Volts -120VAC or 230VAC
Using state-of-the-art, switch-mode technology, the DLS Power Supply series
is engineered with the user and variable environmental conditions in mind.
Extra care has been given to insure many years of service-free operation,
even when subjected to extremely harsh conditions. Batteries are charged
quickly and efficiently without over charging and pumps, motors, and fans
operate perfectly for prolonged life.
IOTA Engineering uses advanced switch mode technology to bring to market
highly sophisticated electronic converter/power supplies at appealing
affordability.
Exceptionally clean DC output insures pumps, motors, fans, and lights work
perfectly. This means longer life for any connected load; virtually no AC
ripple to cause static or premature failure of radio or television
equipment.
|
|
Inverter/Charger Available in 12 - 24- and 48-volt models, it provides
utility-grade output power and offers high surge capacity
105 VAC/60 Hz - 105 VAC/50 Hz - 120 VAC/60 Hz - 220 VAC/60 Hz - 230 VAC/50 Hz-DC
to DC Converters
-DC to DC Converters Din Rail
-Din Rail Linear Power Supplies
-DIN Rail power supplies
-Din Rail Single Phase Power Supplies
-Din Rail Unregulated Line Power Supplies
-Din Rail Voltage Regulator
-Inverters Accessories
-Inverters DC/AC
-Mini Power
-Power Supplies
-Power Transformers
-Transformer |
|
|
GeneralCommunications Wireless Solutions Provider putting the latest RF and
IR technology to work to enhance productivity and increase profits. More than a
radio company, GeneralCommunications Point Wireless combines wireless (RF & IR)
data transmission with extensive array of sensors and application specific
modules suited for a variety of common applications. GeneralCommunications works
closely with OEMs in dozens of industries to capitalize on the benefits of
wireless technology. All products are general purpose in design and appeal to a
broad customer base. Typical deployments include traffic light automation, food
safety, energy management, access control, fire safety and trucking. The
GeneralCommunications value proposition is based on the ability to engineer
application specific solutions ranging from basic telemetry to wireless
networking. This value arises from GeneralCommunications application awareness
and the command of innovative, high value designs. In addition to application
specific solutions, Point Six Wireless also offers a complete line of general
purpose products for the transmission of Ethernet, serial, Modbus, Weigand,
analog, discrete or sensor based data.
|
Automation Wireless Solution Provider
|
|
IQ Sensors
418 -
IQ Sensors 900 -
Wireless I/O -
Software
Industrial Ethernet
Products
|
|
Automation -
Industrial Ethernet
Products - SCADA
|
|
Power Supplies -
Solar Power SCADA |
|
|
BBS Battery backup system (BBs) that provide battery power
to traffic intersections.
|
|
iPhone
Remote Control for Video IP Any Where! |
IQ Traffic control and access control
products
Traffic Signal Monitors .
signal monitors, vehicle detectors, power
supplies, load switches, flashers, bus interface
units, and detector harnesses) that offer value
added benefits for traffic signal cabinets as
well as gate, parking, and/or door operators
|
UPS
backup your traffic systems with IQFuelCell
IQEnergy:
IQ Fuel cells are now available as an
alternative source for renewable energy.
Unlike traditional power generators,
they don't require gasoline to generate
power. They also provide an alternative
to solar generators because they do not
depend on any external power gathering
equipment. These units are compact,
durable, and built to power a wide range
of applications.
The Best Generator Ever!
Applications: Airports, Computer Rooms,
Hospitals, Traffic, UPS |
|
|
Signal Conditioning
(ADAM-3000)
The ADAM-3000 series modules are the most
cost-efficient, field configurable isolation-based signal conditioners
on the market today. These modules are easily installed to protect
your instruments and process signals from the harmful effects of
ground loop, motor noise, and other electrical interference. |
|
|
Remote I/O Module
(ADAM-4000)
In order to provide the best Remote DA&C system
solution to fully fit the request from industrial users, ADAM-4000
series has been improved with two design concepts: Industrial standard
and Intelligent functions. |
|
|
Distributed I/O System
(ADAM-5000)
ADAM-5000 Ethernet I/O system and isolated I/O
modules now available are bringing new communication performance and
system reliability to the ADAM product line, and to the Industrial
Automation industry in general. |
|
|
Smart Web I/O Modules
(ADAM-6000)
ADAM-6000 Smart Web I/O Module is an
industrial-grade Ethernet hub/switch for Ethernet networking solutions
in Industrial Automation environments. It allows users to expand their
industrial networks fast and cost-effectively. |
|
SCADA -
Wireless SCADA systems:
Industrial Automation, Process Automation, Factory Automation,
Machine Control, Motion Control, Process Control & Instrumentation
RF Wireless Solutions, RF, Wireless Data Collection, Industrial RF
solutions, SCADA, wireless SCADA, RF SCADA monitoring, wireless
transceivers
Data from and control signals to pipes, valves and pumps can be sent
wirelessly via our products.
Electric utilities worldwide can use wireless solutions for
monitoring and controlling vital processes in the development and
distribution of electricity including data from substations,
capacitor banks and high tension lines.
Use wireless to link various segments of their infrastructure, and
to monitor and control alarms and sensors.
Contact US Today! |
|
The ADOTT global
leader, providing a full range of industrial DA&C products. With
rich terminal modules and software support, Adott provides
high-speed, high quality yet cost saving products for industrial
requirements. ADOTT plug-in I/O solutions meet all your
requirements in most general purpose Machine Automation
applications. Both positioning control and velocity control are
supported.
|
|
|
|
|
PCI-Bus
Half-size PCI-Bus DA&C cards follow the
industrial standard form factor of half-length ISA and PCI add-on
cards. |
|
|
ISA-Bus
Data acquisition and control hardware generally
performs one or more of the following functions: analog input,
analog output, digital input, digital output and counter/timer
functions. |
|
|
PC/104
Embedded applications offen require specific
features, creating a custom made board with desired features and
characteristics is expensive and time consuming. A simpler and
more cost-effective solution is to add features by incorporating
PC/104 modules. |
|
|
Motion
ADOTT Stepping/Pulse-type Servo Motor Control
Card is designed for general-purpose extreme motion applications.
For advanced applications, we supply Windows DLL drivers and
user-friendly examples to decrease your programming load. |
|
|
MIC-2000
The MIC-2000 series is a family of rugged and
flexible PC compatible industrial computers. Based on open ISA-bus
passive backplane technology, its flexible modular system design
makes upgrades and maintenance simple. With superior mechanical
reliability and bus extension capabilities, the MIC systems are
ideal for use in applications where a harsh or vibrationprone
environment would prohibit the use of a standard office PC or
compatible. |
ADAM-5511
System Specifications PC-based Programmable Standalone
Controller
Main Features
Network Nodes:
32 nodes (ADAM-4000)
Network Nodes:
64
Communication
Protocol: Modbus/RTU
Communication
Network: RS-485
Communication
Port: RS-485 x 1, RS-232 x 1
Programming
Language: C language
I/O Points: 64
(4 I/O slots)
Communication
Speed: up to 115.2 kbps
Introduction
The ADAM-5511 is a PC-based programmable
micro-controller for standalone data acquisition and control system. It¡¦s
IBM-PC compatible hardware and operating system runs programs written in
both assembly and high-level languages. Each system can handle up to four
I/O modules (up to sixty-four I/O points). The system also provides serial
communication ports (RS-232/485), allowing the system to communicate with
other Modbus devices for versatile applications. |
|
|
Battery Charger: 12Volts,
24 Volts, 36Volts, 48 Volts -120VAC or 230VAC
Using state-of-the-art, switch-mode technology, the DLS Power Supply series
is engineered with the user and variable environmental conditions in mind.
Extra care has been given to insure many years of service-free operation,
even when subjected to extremely harsh conditions. Batteries are charged
quickly and efficiently without over charging and pumps, motors, and fans
operate perfectly for prolonged life.
IOTA Engineering uses advanced switch mode technology to bring to market
highly sophisticated electronic converter/power supplies at appealing
affordability.
Exceptionally clean DC output insures pumps, motors, fans, and lights work
perfectly. This means longer life for any connected load; virtually no AC
ripple to cause static or premature failure of radio or television
equipment.
|
|
Inverter/Charger Available in 12 - 24- and 48-volt models, it provides
utility-grade output power and offers high surge capacity
105 VAC/60 Hz - 105 VAC/50 Hz - 120 VAC/60 Hz - 220 VAC/60 Hz - 230 VAC/50 Hz-DC
to DC Converters
-DC to DC Converters Din Rail
-Din Rail Linear Power Supplies
-DIN Rail power supplies
-Din Rail Single Phase Power Supplies
-Din Rail Unregulated Line Power Supplies
-Din Rail Voltage Regulator
-Inverters Accessories
-Inverters DC/AC
-Mini Power
-Power Supplies
-Power Transformers
-Transformer |
|
|
 Note:
To view the above PDF documents, you will need the
free Adobe Acrobat Reader
Wireless Sensors, Wireless Receivers, Wireless Sensors, Wireless
Receivers, high value wireless solutions for the automation and
communications industry!
|
|
